Fire-Lite 411UD - Secondary Station Configuration Details; Secondary Central Station Account Code; Secondary Central Station 24 Hour Test Time; AC Loss Reporting Delay

Program Mode
34
411UD Document #50759 Rev. E 12/09/2008 P/N 50759:E
Secondary Central Station Number Account Code (51 - 54)
The four locations at addresses 51 - 54 default to all '0's. Valid entries are 0 - 9 and A - F. The number of digits
entered must match the format selection. If programming '2, 3, 4 or 5' into address 50, enter three digits (one digit
each in locations 51, 52 and 53 - location 54 is ignored). If programming '0, 1, 6, 7, 8, 9, A, B, C, D or E' into
address 50, enter four digits (one each in locations 51, 52, 53 and 54).
Secondary Central Station Number 24 Hour Test Time (55 - 58)
Use military time when entering the 24 hour 'test' time. The 24 hour test report to phone number 1 takes up four
locations, from addresses 55 - 58. The default is 00:00 (12:00 midnight). The limits for each location are as fol-
lows (do not use values of A - F as entries):
55: enter 0, 1 or 2
56: enter 0 - 9
57: enter 0 - 5
58: enter 0 - 9
Secondary Central Station Number 24/12/8/6 Hour Test Time Interval (59)
The test report sent to the Secondary phone number may be sent every 6, 8, 12 or 24 hours. If the message is to be
sent every 24 hours, leave the factory default entry of '0'. If other test report times are needed, enter 1 = 12 hour,
2 = 8 hour or 3 = 6 hour.
AC Loss Reporting Delay (60)
Enter a digit of 0 - 9 or A - F corresponding to the number of hours to be delayed in reporting the loss of AC
power. The factory default is '2' for 2 hour delay. The valid entries are '0' = no delay; '1' = 1 hours; '2' = 2 hours;
'3' = 6 hours; '4' = 7 hours; '5' = 8 hours; '6' = 9 hours; '7' = 10 hours; '8' = 11 hours; '9' = 12 hours; 'A' = 13 hours;
'B' = 14 hours; 'C' = 15 hours; 'D' = 16 hours; 'E' = 17 hours; 'F' = 18 hours. Note: Use when the host panel has a
dedicated relay output. Verify the delay period programmed at the host panel. Location 60 is valid for all inputs
programmed as AC Loss.
216 Secondary # Input Channel 2 Active Restoral Code E
217 Secondary # Input Channel 3 Active Restoral Code E
218 Secondary # Input Channel 4 Active Restoral Code 9
219 Secondary # Input Channel 1 Fault Restoral Code D
220 Secondary # Input Channel 2 Fault Restoral Code D
221 Secondary # Input Channel 3 Fault Restoral Code D
222 Secondary # Input Channel 4 Fault Restoral Code D
223 Secondary # Phone Line 1 Restoral Code A
224 Secondary # Phone Line 2 Restoral Code A
225 Secondary # Phone Number 1 Restoral Code A
226 Secondary # Phone Number 2 Restoral Code A
227 Secondary # System Off Normal Restoral Code A
228 Secondary # System Test Message 9
229 Secondary # System Abnormal Test Message F
230 Secondary # Upload/Download Request Code 7
231 Secondary # Upload Successful Code 7
232 Secondary # Download Successful Code 7
233 Secondary # Upload/Download Failed Code 7
TABLE 3-6: All 3+1, 4+1 and 4+2 Expanded Formats - Secondary
Address Description Setting