What to do if my FireAngel Smoke Alarm activates with no smoke?
If your FireAngel smoke alarm activates even when there's no visible smoke, first, check its location based on the 'Application' guidelines. Then, proceed to clean the smoke alarm following the instructions in the 'Maintenance' section.
How to test my FireAngel ST-625 Smoke Alarm if it doesn't sound?
If your FireAngel smoke alarm doesn't sound during testing, ensure you allow a few seconds for the alarm to settle, especially after initial activation or battery replacement. Also, make sure you firmly push the center of the test button. If the unit has been silenced and is in low sensitivity mode, wait 15 minutes before trying again. If the alarm was recently installed and still fails the self-test, contacting Technical Support is advisable.
Why doesn't the silence chirp work on my FireAngel ST-625?
If the silence chirp function doesn't work when you press the test button on your FireAngel Smoke Alarm, and the red LED flashes separately from the chirp, this indicates a fault. In this case, or if the alarm is within its warranty period, contact Technical Support. Otherwise, replace the alarm immediately.
Guidance on fitting smoke alarms in existing homes based on recommendations.
Advice for using smoke alarms in flats, bedsits, and shared accommodations.
Use of smoke alarms in motels, hospitals, day care, and similar facilities.
Suitability of the smoke alarm for use in mobile homes and caravans.
States the smoke alarm is not intended for commercial or industrial use.
Instructions for inserting batteries into the smoke alarm correctly.
Steps for attaching the base plate to the ceiling or wall.
Guidance on attaching the alarm unit to the fitted base plate.
Procedure for testing the smoke alarm after installation.
Describes the expected LED flashing for normal operation.
Explains the audible chirp for low battery and recommended actions.
Lists the recommended battery types for replacement.
Temporarily silences false alarms by pressing the test button.
Alarm enters reduced sensitivity mode for 10 mins; LED flashes every 10 secs.
Alarm automatically returns to full sensitivity; LED reverts to flashing every 40 secs.
Temporarily silence low battery chirps for 8 hours by pressing the test button.
Recommends testing the smoke alarm weekly.
Recommends cleaning the unit every 3 months with a vacuum cleaner.
Solutions for when the smoke alarm fails to sound during testing.
Solutions for intermittent chirping from the smoke alarm.
Solutions for false alarms when no smoke is present.
Troubleshooting steps if the low battery warning cannot be silenced.
Solutions for experiencing frequent false alarms.
Details the 5-year limited warranty, exclusions, and liabilities.
Guidance on fitting smoke alarms in existing homes based on recommendations.
Advice for using smoke alarms in flats, bedsits, and shared accommodations.
Use of smoke alarms in motels, hospitals, day care, and similar facilities.
Suitability of the smoke alarm for use in mobile homes and caravans.
States the smoke alarm is not intended for commercial or industrial use.
Instructions for inserting batteries into the smoke alarm correctly.
Steps for attaching the base plate to the ceiling or wall.
Guidance on attaching the alarm unit to the fitted base plate.
Procedure for testing the smoke alarm after installation.
Describes the expected LED flashing for normal operation.
Explains the audible chirp for low battery and recommended actions.
Lists the recommended battery types for replacement.
Temporarily silences false alarms by pressing the test button.
Alarm enters reduced sensitivity mode for 10 mins; LED flashes every 10 secs.
Alarm automatically returns to full sensitivity; LED reverts to flashing every 40 secs.
Temporarily silence low battery chirps for 8 hours by pressing the test button.
Recommends testing the smoke alarm weekly.
Recommends cleaning the unit every 3 months with a vacuum cleaner.
Solutions for when the smoke alarm fails to sound during testing.
Solutions for intermittent chirping from the smoke alarm.
Solutions for false alarms when no smoke is present.
Troubleshooting steps if the low battery warning cannot be silenced.
Solutions for experiencing frequent false alarms.
Details the 5-year limited warranty, exclusions, and liabilities.
General| Type | Optical Smoke Alarm |
|---|---|
| Sensor Type | Optical |
| Battery Life | Up to 10 years |
| Alarm Sound Level | 85 dB at 3 meters |
| Test Button | Yes |
| LED Indicator | Yes |
| Weight | 200g |
| Standards Compliance | EN 14604 |
| Operating Temperature | 0°C to 40°C |
| Dimensions | 130mm x 130mm x 45mm |
To Next Page