FLIR
Commercial S
y
stems,
2017.
All
rights
rese
r
v
ed
worldwide.
No
parts
of this manual
, in
whole or in
part,
may
be copied
, photocopied, translated, or
transmitted
to any
electro
n
ic
medium
or machine
-readable
form w i t h ou t
the
p r i o r w ri tt e n
permission
of FLIR
Commercia
l
Sy
stems
Names
and mark s
appearing
on the p r o d u c t s
herein are either registered trademarks or
trademarks
of FLIR
Commercial Systems
and/or
its subsidiaries
.
All
other trademarks, trade names,
or company
names referenced
herein are used
for
identification
only and are
the
property
of
their respective owners.
Liberation fonts are copyright
2009
by
RedHat
and are
used under authority
of the GNU
publi
c
l
i
cense.
Information about these fonts
and the GN U
pub
l
ic
license
can be found at
:
https://www
.redhat.com/promo/fonts/.
This
product
i
s
protected
by
patents, design patents, patents pending,
or design
p
atents
pendi
ng.
If
you have que stions
that are
not covered
in this manual
,
or need
ser
v
ice,
contact
FLIR
Commercial Systems
Technical Support
at SBA-Cores@flir.com
for
additional information
prior to
returning a came
ra.
This documentation and the requirements specified herein are subject to change without notice.
This
equipment must
be disposed
of
as electronic
waste.
Contact
your
nearest
FLIR
Commerci
a
l
Systems,
Inc.
representative
for
instructions
on how to
return
the p r o d u c t
to FLIR for
proper
di
sposal
.
FCC Notice. This device is a subassembly designed for incorporation into other products in order to provide an infrared camera
function. It is not an end-product fit for consumer use. When incorporated into a host device, the end-product will generate, use,
and radiate radio frequency energy that may cause radio interference. As such, the end-product incorporating this subassembly
must be tested and approved under the rules of the Federal Communications Commission (FCC) before the end-product may be
offered for sale or lease, advertised, imported, sold, or leased in the United States. The FCC regulations are designed to provide
reasonable protection against interference to radio communications. See 47 C.F.R. §§ 2.803 and 15.1 et seq.
Industry Canada Notice. This device is a subassembly designed for incorporation into other products in order to provide an infrared
camera function. It is not an end-product fit for consumer use. When incorporated into a host device, the end-product will generate,
use, and radiate radio frequency energy that may cause radio interference. As such, the end-product incorporating this subassembly
must be tested for compliance with the Interference-Causing Equipment Standard, Digital Apparatus, ICES-003, of Industry Canada
before the product incorporating this device may be: manufactured or offered for sale or lease, imported, distributed, sold, or leased
in Canada.
Avis d’Industrie Canada. Cet appareil est un sous-ensemble conçu pour être intégré à un autre produit afin de fournir une fonction
de caméra infrarouge. Ce n’est pas un produit final destiné aux consommateurs. Une fois intégré à un dispositif hôte, le produit final
va générer, utiliser et émettre de l’énergie radiofréquence qui pourrait provoquer de l’interférence radio. En tant que tel, le produit
final intégrant ce sous-ensemble doit être testé pour en vérifier la conformité avec la Norme sur le matériel brouilleur pour les
appareils numériques (NMB-003) d’Industrie Canada avant que le produit intégrant ce dispositif puisse être fabriqué, mis en vente
ou en location, importé, distribué, vendu ou loué au Canada.
EU Notice. This device is a subassembly or component intended only for product evaluation, development or incorporation into
other products in order to provide an infrared camera function. It is not a finished end-product fit for general consumer use. Persons
handling this device must have appropriate electronics training and observe good engineering practice standards. As such, this
product does not fall within the scope of the European Union (EU) directives regarding electromagnetic compatibility (EMC). Any
end-product intended for general consumer use that incorporates this device must be tested in accordance and comply with all
applicable EU EMC and other relevant directives.
To Previous Page
Loading...
