How to stop the FLIR DVR system from beeping during motion detection?
The system beeps during motion detection because motion detection is enabled and the alarm buzzer is activated. To disable it, go to the Main Menu, click Event>Motion>Motion Detect, uncheck Buzzer for each channel, and click Apply.
Why is there no picture on my monitor/TV after connecting it to the FLIR M4200 DVR system?
There might be several reasons: * The monitor/TV may not be detected by the system. Try powering off both the monitor/TV and the DVR system, then power on the monitor/TV first, followed by the system. * The input channel for the system may not be selected on the monitor/TV. Ensure that you select the correct input channel on your monitor/TV to which the DVR system is connected. * The video cable might be loose or disconnected. Check the video cable connection at both the DVR system and the monitor/TV.
What to do if my FLIR DVR system is not receiving power or not powering up?
If your FLIR DVR system isn't powering up, here's what to check: * Ensure the cable from the power adapter is securely connected to the back of the unit and to the power outlet. * Verify that the power switch is in the ON (I) position. * Confirm the system is powered on by checking for LED indicators on the front. * If connected to a power bar or surge protector, try connecting directly to the wall outlet. * Test the outlet with another device or try a different outlet.
Why is my hard drive full on my FLIR DVR (0%) and the unit is no longer recording?
The hard drive might be full because the overwrite function is not enabled. To resolve this, go to the Main Menu, then navigate to Setting>General>General. Under HDD Full, select Overwrite and click OK.
What to do if the mouse is not detected by my FLIR DVR system?
If your mouse isn't being detected by the FLIR DVR system: * Make sure the mouse cable is firmly connected to one of the USB ports. * If that doesn't work, power off the system (disconnect the power cable), firmly connect the USB mouse to a USB port, and then reconnect the power cable.
Why is the hard drive not detected by my FLIR M4200 DVR system?
The hard drive may not be detected for these reasons: * The hard drive cables might be loose or not properly connected. Remove the housing and check that the hard drive cables are firmly connected. * There might not be a hard drive installed in the system. Open the housing and install a compatible hard drive. Remember to format the drive after installing it.
Why is there no picture on selected channels, or why is the camera picture not being displayed on my FLIR M4200 DVR?
The issue could be due to loose or disconnected camera cables. Check the camera video cable and connections, disconnect and reconnect the cable at both the system and the camera. You can also try moving the camera to another channel or using another cable.
Guidance on safe usage, cleaning, ventilation, and power connection for the product.
Instructions for proper installation, including reading instructions and heeding warnings.
Guidelines for servicing the product and conditions requiring professional service.
Instructions for proper usage, cleaning, and handling of the product.
Explains the function of playback controls, function buttons, and directional buttons on the front panel.
Describes the IR receiver for remote control and the status indicated by POWER, HDD, and NET LEDs.
Identifies and describes the ports for M3200 series DVRs, including M3204 and M3208/M3216 models.
Identifies and describes the ports for M4200 series DVRs, including M4204 and M4208 models.
Instructions for connecting FLIR MPX or analog cameras to the DVR's video input ports.
Instructions for connecting the USB mouse to the DVR's USB port.
Instructions for connecting the DVR to a network router using an Ethernet cable.
Instructions for connecting an HDMI or VGA monitor to the DVR for viewing the system interface.
Steps to connect the power adapter and turn on the DVR system.
Guidance on checking for and installing the latest system firmware version.
Procedures for checking camera video quality before permanent mounting.
Instructions for setting the system's date and time for accurate video timestamps.
Provides default login credentials and port numbers for system access and FLIR Cloudâ„¢.
Information about FLIR Cloudâ„¢ service for easy internet connection without network configuration.
Method to quickly view vital system information through the Quick Menu or front panel.
Details compatible cabling types and maximum run lengths for MPX systems.
Procedure to pair the remote control with a specific system if multiple systems are present.
Identifies and describes the components of the DVR's live view display area.
How to access and use the Quick Menu for system functions like View, Search, and Main Menu.
Procedure for adjusting Hue, Brightness, Contrast, and Saturation for camera image quality.
Explains the functions of the Navigation Bar for quick access to menus and settings.
Describes the icons and functions available in the Camera Toolbar for specific channel actions.
How to quickly play back the last 5-60 minutes of recorded video from a selected channel.
How to activate and use digital zoom to magnify specific areas in the live camera view.
Procedure for saving live footage to a USB drive or external hard drive.
Explains the use of the on-screen virtual keyboard for text and numeric input in menus.
Describes Continuous and Motion-based recording modes, indicated by icons.
Explanation of the two video streams (Main for quality, Sub for efficiency) and their uses.
How to configure recording based on a schedule or manually turn recording on/off.
Setting options for overwriting old recordings or stopping recording when the hard drive is full.
Steps to enter Search mode, use the calendar, select channels, and select playback time.
Details the various controls for navigating and managing video playback.
Procedure to play back video files stored on an external USB drive.
Recommended steps for formatting a USB drive before using it for backup.
Steps to search for and back up video files to a USB drive, including file format options.
How to select a duration of video during playback and save it as a clip to a USB device.
Information on playback software for .dav backup files on PC and Mac.
Instructions for downloading and installing the Video Player for PC.
Instructions for downloading and installing the Video Player for Mac.
Procedure for modifying the system password for admin and user accounts.
Steps to create new user accounts with specific permissions and access levels.
How to edit user account details, including permissions and group assignments.
Procedure for removing user accounts from the system.
Explanation of how account groups simplify permission management for users.
Steps to create new groups and assign permissions to them.
How to edit the details and permissions of existing account groups.
Procedure for removing account groups from the system.
Accessing the Camera menu for configuring image settings, recording, and channel names.
Details on setting recording parameters like resolution and frame rate for cameras.
How to adjust quality settings for Main and Sub Streams, including resolution, frame rate, and bit rate.
Steps to enable and configure audio recording for a selected channel.
Setting up snapshot captures triggered by motion detection or schedules.
How to assign custom names to cameras for easier identification.
Guidance on selecting cable type (UTP/Coaxial) for image quality issues.
Viewing details about installed hard drives, including capacity and status.
Displaying start and end times of recordings saved on the hard drive.
Checking the current firmware version installed on the system.
Displaying system alarms, motion detection status, and other relevant alerts.
Viewing a list of users currently connected to the system via computers or mobile devices.
Monitoring the network traffic the system is sending and receiving.
Testing system connectivity to other devices over LAN or Internet using IP addresses.
Showing the bitrates of connected cameras, indicating data transmission amounts.
Searching and viewing system logs, with options to export them.
Configuring network parameters for the system, including IP address settings.
Setting up IP address configuration using DHCP (recommended) or a static IP address.
Setting up ports for system connection, including HTTP and Client ports.
Steps for setting up FLIR DDNS for remote access, including account registration.
Setting up email notifications for system events like motion detection or video loss.
Accessing settings for motion detection, video loss, and system warnings.
Setting up motion detection parameters, including regions, sensitivity, and threshold.
Setting up responses to video loss events, including alarms, messages, and recording.
Connecting and configuring external alarm input devices like motion sensors.
Enabling or disabling alarm output devices and manually activating them.
Setting up notifications for hard drive issues like 'No Disk', 'Disk Error', or 'Disk Full'.
Setting up notifications for network issues like disconnection, IP/MAC conflicts.
Accessing storage configurations for recording schedules and hard drives.
Setting up custom recording schedules based on time, day, and recording type.
Setting the duration for pre-recording video when motion detection events occur.
Setting up a schedule for when snapshot images are recorded from cameras.
Setting specific days as holidays to apply special recording schedules.
Steps to format a new or existing hard drive using the HDD Manager.
Selecting the type of HDD (Read-write, Read-only, Mirroring) for system operation.
Advanced configuration for automatic video backup using a mirror hard drive.
Adjusting miscellaneous system settings like language, video standard, and mouse speed.
Configuring display settings, including monitor resolution and menu transparency.
Setting up RS232 communication for connecting a FLIR PTZ keyboard.
Procedure to back up current system settings to a USB thumb drive.
Steps to reset the system to its original factory default settings.
Instructions for upgrading the system's firmware using a USB drive.
How to log out, shut down, or restart the system.
Lists the hardware and software requirements for connecting to the system over the internet.
Steps to connect the DVR system to a router using an Ethernet cable.
How to find the unique Device ID required for FLIR Cloudâ„¢ connection.
Instructions for downloading, installing, and launching the FLIR Cloudâ„¢ Client software.
Overview of the client software's home page and navigation tabs.
How to view live video from connected systems using the FLIR Cloudâ„¢ client.
Description of the controls within the Live View interface, including camera toolbar and split-screen options.
Instructions for using multiple monitors to view live camera feeds simultaneously.
How to control PTZ cameras using the FLIR Cloudâ„¢ client software.
Details the PTZ controls for moving, zooming, focusing, and accessing advanced features.
How to save and recall specific camera positions using PTZ presets.
Setting up tours to cycle through a sequence of PTZ presets.
Defining patterns to automatically cycle a camera between two positions.
Setting up scans to automatically cycle between left and right points.
Enabling continuous 360° pan movement for PTZ cameras.
How to access and use playback mode to view recorded video from connected systems.
Details the playback controls for navigating video, adjusting speed, and managing files.
Instructions for downloading video files from the system to a computer's hard drive.
How to view a list of alarms received by the client software and manage them.
Viewing logs for the client software or logs from connected systems.
How to create virtual maps of cameras over floor plans for intuitive navigation.
Managing systems connected to the client software, including adding, deleting, and editing.
Remotely configuring settings for connected systems via the client software.
Setting up alarms within the client software for event notifications and alerts.
Setting up custom views and tours for automatic cycling of camera feeds.
Managing user accounts and passwords for the FLIR Cloudâ„¢ client software.
Adding user accounts with customized access levels and permissions.
Creating and managing roles to define permissions for user accounts.
Configuring general application settings for the FLIR Cloudâ„¢ client software.
Adjusting settings like log save time, instant playback, network capability, and auto login.
Selecting folders for saving snapshots and downloaded video files.
Configuring audio alerts for events and customizing alarm sounds.
Checking the version of the client software and recommending updates.
Requirements for connecting an iPhone or iPad to the system, including firmware and network setup.
Steps to download, install, and configure the FLIR Cloudâ„¢ app on an iPhone.
Overview of the Live View interface on the iPhone app, including controls and navigation.
How to control PTZ cameras using the FLIR Cloudâ„¢ app on an iPhone.
Details the PTZ controls available within the iPhone app.
Accessing and viewing saved snapshots and videos using the app's Local Files feature.
How to access and use playback mode on an iPhone to view recorded video.
Setting up push notifications for motion detection events on the iPhone.
Viewing a list of events received via push notifications on the iPhone.
Saving and quickly accessing groups of cameras as favorites in the iPhone app.
Creating and using E-Maps to place cameras on a visual map within the iPhone app.
Managing systems within the iPhone app, including adding, deleting, and editing connections.
Advanced method to connect to systems using IP or DDNS addresses on iPhone.
Requirements for connecting an iPad to the system, including firmware and network setup.
Steps to download, install, and configure the FLIR Cloudâ„¢ app on an iPad.
Overview of the Live View interface on the iPad app, including controls and navigation.
How to control PTZ cameras using the FLIR Cloudâ„¢ app on an iPad.
Details the PTZ controls available within the iPad app.
How to access and use playback mode on an iPad to view recorded video.
Accessing and viewing saved recordings using the app's Local Files feature on iPad.
Setting up push notifications for motion detection events on the iPad.
Viewing a list of events received via push notifications on the iPad.
Saving and quickly accessing groups of cameras as favorites in the iPad app.
Creating and using E-Maps to place cameras on a visual map within the iPad app.
Managing systems within the iPad app, including adding, deleting, and editing connections.
Advanced method to connect to systems using IP or DDNS addresses on iPad.
Requirements for connecting an Android device to the system, including firmware and network setup.
Steps to download, install, and configure the FLIR Cloudâ„¢ app on an Android device.
Overview of the Live View interface on the Android app, including controls and navigation.
How to control PTZ cameras using the FLIR Cloudâ„¢ app on an Android device.
Details the PTZ controls available within the Android app.
Accessing and viewing saved recordings using the app's Local Files feature on Android.
How to access and use playback mode on an Android device to view recorded video.
Setting up push notifications for motion detection events on Android devices.
Viewing a list of events received via push notifications on Android devices.
Saving and quickly accessing groups of cameras as favorites in the Android app.
Creating and using E-Maps to place cameras on a visual map within the Android app.
Managing systems within the Android app, including adding, deleting, and editing connections.
Advanced method to connect to systems using IP or DDNS addresses on Android.
Steps to confirm network connectivity within a local area network before DDNS setup.
Connecting the DVR system to the router as a prerequisite for DDNS setup.
Finding the system's local IP address using the Quick Menu.
Confirming connectivity over a local network using the client software.
Port forwarding HTTP and Client ports on the router to the system's IP address.
Steps to register for a free FLIR DDNS account for remote access.
Enabling DDNS settings within the system's Main Menu.
Connecting to the system remotely using the configured DDNS address.
Steps for physically connecting PTZ cameras and configuring them for control.
Specific configuration steps for analog PTZ cameras, including serial settings.
Using the DVR's interface to control PTZ camera movement and zoom.
Details the primary controls for operating PTZ cameras.
Accessing advanced PTZ functions like presets, tours, patterns, and auto scans.
How to save and recall specific camera positions using PTZ presets.
Setting up tours to cycle through a sequence of PTZ presets.
Defining patterns to automatically cycle a camera between two positions.
Setting up scans to automatically cycle between left and right points.
Procedure for physically installing a hard drive, including screw and cable connections.
Instructions for safely removing a hard drive from the DVR system.
Procedure for formatting hard drives before they can be used by the system.
Details on FCC rules and measures to correct potential radio or television interference.
Caution against unauthorized modifications that could void user authority.
Statement confirming product compliance with the EU Restriction of Hazardous Substances directive.
To Next Page
General
