Fluke 113 User Manual

Model 113 English Instruction Sheet
Page 1
®
113
Electrical Multimeter
Instruction Sheet
Safety Information
A Warning statement identifies hazardous conditions and actions
that could cause bodily harm or death.
A Caution statement identifies conditions and actions that could
damage the Meter or the equipment under test.
To avoid possible electric shock or personal injury,
follow these guidelines:
• Use the Meter only as specified in this instruction sheet
or the protection provided by the Meter might be
impaired.
• Do not use the Meter or test leads if they appear
damaged, or if the Meter is not operating properly.
• Always use proper terminals, switch position, and range
for measurements.
• Verify the Meter's operation by measuring a known
voltage. If in doubt, have the Meter serviced.
• Do not apply more than the rated voltage, as marked on
Meter, between terminals or between any terminal and
earth ground.
• Use caution with voltages above 30 V ac rms, 42 V ac
peak, or 60 V dc. These voltages pose a shock hazard.
• Disconnect circuit power and discharge all high-voltage
capacitors before testing resistance, continuity, diodes,
or capacitance.
PN 3083192 December 2007, Rev. 1, 12/08
©2007, 2008 Fluke Corporation. All rights reserved.
Specifications subject to change without notice. Printed in China

Fluke 113 Specifications

General

Backlight	Yes
Product type	Digital multimeter
Frequency range	0.5 - 1 kHz
AC voltage range	2000 - 0.001 V
DC voltage range	6000 - 0.001 V
Capacitance range	1000 - 1 nF
Resistance resolution	0.1 Ω
Resolution (DC voltage)	0.1 mV
Basic accuracy (DC current)	2.0% + 3
Basic accuracy (capacitance)	1.9% + 2 100 μF - 1000 μF: 1.9% + 2 1000 μF: 5% + 20
Temperature measurement range	-10 - 50 °C
Dimensions (WxDxH)	167.1 x 85.1 x 46 mm
Battery voltage	9 V

Weight and Dimensions

Weight	404 g

Summary

Safety Information

Warning and Caution Statement Definitions

Defines the meaning of Warning and Caution statements for hazardous conditions.

General Safety Guidelines

Lists critical guidelines to prevent electric shock or personal injury, covering various usage scenarios.

Symbols and Terminals

Understanding Measurement Symbols

Explains common symbols used on the meter and their significance.

Identifying Input Terminals

Describes the function of the common (return) and input terminals on the multimeter.

Range Selection Modes

Automatic Range Selection

Explains that the meter defaults to autoranging upon power-up.

Manual Range Selection

Details how to switch to manual range mode for specific functions.

Meter Features

Battery Saver (Sleep Mode)

Describes how the meter enters sleep mode to conserve battery and how to resume operation.

Backlight Control

Explains how to control the backlight and its automatic turn-off feature.

Display Hold Functionality

Details how to activate and deactivate the display hold function to freeze readings.

Power-Up Options

Configuring Power-Up Options

Explains how to select power-up options by holding buttons during power-on.

CHEK Function and Voltage Measurement

CHEK Mode Operation Details

Describes how the CHEK mode operates, including auto-switching and low impedance.

AC/DC Voltage Measurement

Refers to CHEK for voltage measurements and specifies input impedance.

Diode Test

Testing Good Diodes

Illustrates how to test good diodes in forward and reverse bias.

Identifying Bad Diodes

Shows how to identify bad diodes (open or shorted) during testing.

Continuity Testing

Standard Continuity Test

Explains how to perform continuity tests, noting power-off requirement.

Continuity Capture Function

Describes the continuity capture feature and its response time.

Continuity Capture Details

Managing Continuity Transitions

Details how to reset the display and exit the continuity capture mode.

Resistance and Capacitance Measurement

Measuring Resistance

Explains how to measure resistance and the required power-off condition.

Measuring Capacitance

Details how to measure capacitance, including power-off and discharge steps.

MIN MAX Recording

MIN MAX Recording Modes

Explains how the meter records minimum, maximum, and average readings.

Entering and Exiting MIN MAX

Describes the process of entering, navigating, and exiting MIN MAX mode.

Maintenance and Service

Disabling the Beeper

Explains how to disable the beeper function by holding a button during power-on.

Cleaning and Care Instructions

Provides instructions on how to clean the meter case and avoid damage.

Battery Replacement Procedure

Outlines the steps for replacing the meter's battery.

Contacting Service Centers

Lists contact information for authorized service centers and the website.

Specifications Overview

Accuracy Specifications

Details the accuracy specifications for various functions and ranges.

Measurement Notes and Conditions

Provides important notes regarding Chek, crest factor, and wait times for measurements.

Detailed Specifications

Operating and Environmental Specs

Lists operating and storage temperatures, altitude, and humidity.

Battery, Shock, Vibration, Safety

Covers battery type, life, shock, vibration standards, and safety compliance.

EMI Regulations and Certifications

Details EMI regulations and product certifications.

Technical Parameters

Chek Input Impedance and CMRR

Specifies the nominal input impedance and common mode rejection ratio for Chek function.

Resistance and Diode Test Parameters

Lists open circuit test voltage, full scale voltage, and short circuit current for resistance and diode tests.

MIN MAX Accuracy and Response

Provides accuracy and response time specifications for MIN MAX recording.

Limited Warranty & Limitation of Liability

Product Warranty Terms

Outlines the three-year warranty period and exclusions for the product.

Liability Limitations

Details limitations on implied warranties and consequential damages.