What to do if the Focal Speaker System remote control is not working?
If the remote control for your Focal Speaker System is not working, consider the following: * Ensure that the Dimension is within reach of the remote control and that the angle is not too extreme. The remote control has a reach of approximately 7 meters and a maximum angle of 20°. * The battery in your remote control may be low. Try replacing the battery.
Why is there no sound from Focal Speaker System when using Audio Return Channel?
If your TV has the Audio Return Channel function but there is no sound when Dimension’s TV input is selected on your Focal Speaker System: * The Audio Return Channel function on your TV may be deactivated. Refer to your TV’s user manual and enable the TV’s Audio Return Channel function. * The HDMI™ cable may not be connected correctly, or there may be a fault with the cable. Check the connections and try another HDMI™ cable.
How to synchronize audio and video on Focal Speaker System?
If the audio and video are not synchronized on your Focal Speaker System, it might be because your TV is not equipped with an automatic synchronization function. Try using Dimension’s manual "SYNC" function.
What to do if no sound is coming from Dimension Sub subwoofer of Focal Speaker System?
If no sound is coming from your Dimension Sub subwoofer with your Focal Speaker System: * Check that the cable is connected correctly. * Verify that the "SUBWOOFER" selector is set to 11 - "DIMENSION SUBWOOFER OUT".
Why is there no sound from the subwoofer connected to SUB LINE OUT of Focal Speaker System?
If there is no sound from the subwoofer connected to the SUB LINE OUT output on your Focal Speaker System: * Ensure the cable is connected correctly. * Check that the "SUBWOOFER" selector is set to 12 - SUB LINE OUT. * Confirm that your active subwoofer is working correctly and is not set to OFF or Standby.
How to fix CEC issues with Focal Speaker System via HDMI?
If the CEC via the HDMI™ connections are not working correctly on your Focal Speaker System, the CEC command via HDMI™ may be deactivated on your audio-video devices. Enable this function on the audio-video devices connected to Dimension.
What does it mean when the Standby button is flashing and the volume + button is lit on my Focal Speaker System?
If no sound is coming from your Focal Speaker System Dimension, the Standby button is flashing, and the volume + button is lit, the overheating protection has been activated due to excessive amplifier temperature. Unplug the system, wait for an hour until it cools down, then turn Dimension back on.
Why is there no sound and the HDMI button is lit on my Focal Speaker System?
If no sound is coming from your Focal Speaker System Dimension, the Standby button is flashing, and the HDMI™ TV button is lit, the overheating protection has been activated due to overcurrent. Unplug the system, wait for an hour until it cools down, then turn Dimension back on.
What to do if the Standby button is flashing and other buttons are lit on my Focal Speaker System?
If no sound is coming from your Focal Speaker System Dimension, the Standby button is flashing, and one or two other buttons are lit, Dimension’s microprocessor has stopped working due to a considerable electric shock. Unplug the system, wait for five minutes, then turn Dimension back on.
Why is there no sound coming from my Focal Speaker System?
If there is no sound coming from your Focal Speaker System, there are several possible causes: * The cables may not be connected correctly, or there may be a fault with one or more cables. Check the connections and try interchanging the cables. * The desired source may not be selected. Use the remote control (input button) or the user interface to select the correct source. * The volume may be set to minimum, or the Mute function may be activated. Adjust the volume using the + or - buttons, or deactivate the Mute function. * Your audio-video source may be transmitting an audio format not recognised by the Dimension. In the source settings, select an audio format supported by Dimension. * The HDMI™ devices connected to Dimension may not support HDCP (High-Bandwidth Digital Conten...
Essential safety guidelines and warnings for operating the device.
Details of the various input and output ports available on the device.
Guide to using the infrared remote control for device functions.
Recommendations for optimal placement and physical installation of the soundbar.
Explanation of selectors for adjusting sound based on environment.
Detailed guide on connecting various audio and video sources to the soundbar.
How to connect the soundbar to a television using HDMI or optical cables.
Connecting external devices like Blu-ray players to the HDMI In port.
Comprehensive guide on using the soundbar's various operational modes and features.
Solutions for common problems encountered with the soundbar.
Information and precautions for installing the Dimension Sub subwoofer.
General| Audio decoders | - |
|---|---|
| RMS rated power | 450 W |
| Audio output channels | 5.1 channels |
| Subwoofer included | Yes |
| Subwoofer frequency range | 30 - 110 Hz |
| Product color | Black |
| Apple docking compatibility | Not supported |
| Soundbar dimensions (WxDxH) | 1155 x 115 x 115 mm |
| Subwoofer dimensions (WxDxH) | 1155 x 325 x 115 mm |
| Digital audio optical out | 1 |
Weight and Dimensions| Soundbar weight | 5500 g |
|---|---|
| Subwoofer weight | 14000 g |
To Next Page
