DIMENSION
User
manual
•
When the
signals
have been synchronised, exit
the
synchronisation
mode by pressing
the@
button
on
your
remote
control
again. Synchronisation
adjustments
vary depending
on
the input.
You
can
adjust
the
synchronisation
of
the
audio and video
differently
for
the
various
inputs,
thus
for
your
different
devices.
Note: If you
want
to restore the
programmed
delay
default
[factory
settings]
or
automatic
synchronisation
on HDMI™
In, press the
G
button
on
the
remote
control
or
user
interface
until
the
bar
display
volume
are
all
extinct.
8.
9.
Light
function
The
user
interface
light
is
normally
off.
You
can
turn
it on
for
a
few
seconds
by
pressing
the
"Light"
button
on
your
remote
control.
9.
Troubleshooting
Refer to the
table
below
if you
encounter
any
problems
with
Dimension. If the
problem
persists,
or
if none of the
solutions
proposed solve the
problem,
turn
Dimension
off and contact
your
dealer
or
Focal's
authorised
After
Sales
Service.
No sound is
coming
from
The overheating
protection
Unplug
the system,
wait
for
Dimension, the Standby
has been activated due
I
button
is
flashing
and the
to excessive
amplifier
an
hour
until
it cools down,
volume
+
button
is lit.
then
turn
Dimension
back on.
No sound is
coming
from
The overheating
protection
Unplug
the system,
wait
for
Dimension, the Standby
but-
I
ton is
flashing
and the
HDMITM
has been activated due to
an
hour
until
it cools down,
TV
button
is lit.
overcurrent.
then
turn
Dimension
back on.
No sound is
coming
from
Dimension's
microprocessor
Unplug
the system,
wait
Dimension, the Standby
I
button
is
flashing
and one
or
has stopped
working
due to
for
five
minutes,
then
turn
two
other
buttons
are lit.
a
considerable
electnc
shock.
Dimension
back on.
The cables have not been
Check connections.
No sound
connected
correctly
or
there
If the
hroblem
persists,
Page
18
is a
fault
with
one
or
more
cables.
interc
ange the cables.
Select the desired source
The desired source has not
using the
remote
control
Page 8 &
10
been selected.
[input
button]
or
the
user
interface.
The
volume
is set to
Adjust
the
volume
according
minimum
or
the
Mute
to the desired level using the
Page
10
function
has been activated.
+
or
- buttons,
or
deactivate
the Mute
function.
Your audio-video source is
In the source
settings,
select
transmitting
an audio
format
an audio
format
supported
by
Page
25
not Dimension.
Dimension.
The HDMI™ devices
connected to
Dimension
do
Connect an audio-video
not
support
HDCP
device
which
supports
HDCP.
I
[High-Bandwidth
Content
No sound is
coming
from
your
The cable has not been
Check the cable
Dimension
Dimension
Sub subwoofer.
connected
correctly
or
there's
is connected correctly.
Sub
user
a
fault
with
the cable.
manual
The "SUBWOOFER"
selector
Check
that
the
"SUBWOOFER"
selector
setting
is positioned
is set to
11
-"DIMENSION
Page
17
in correctly.
SUBWOOFER OUT".
To Next Page
Loading...
