Focus Industries Handler I

Questions and Answers

D
Douglas ForbesAug 17, 2025
What to do if the Focus Industries Farm Equipment venturi won’t suck?
- Z
  Zachary LopezAug 17, 2025
  If the venturi isn’t sucking, start by checking its installation to ensure it's in the correct direction and the nozzle is properly placed. Also, verify that the discharge line is large enough to handle the mixture flow; it should be at least the size of the venturi package fittings (2” or 3”, depending on the model). Finally, inspect the lines for any obstructions, which can be done by connecting a hose directly from the venturi to the top of the sprayer tank, bypassing the sprayer plumbing.
T
Thomas McguireAug 19, 2025
What to do if Focus Industries Farm Equipment threaded fittings leak?
- B
  bryanttimothyAug 20, 2025
  If threaded fittings are leaking, ensure you're using the sealant properly, following the manufacturer's instructions. Remember to store and apply the sealant between 20°F and 140°F on clear tapered threads. For pipes up to 1 1/4”, apply a thick, even coat to male threads only; for larger sizes, apply to both male and female threads. Tighten up to 3 full turns past hand tight for pipes up to 2”, and up to 2 full turns for larger sizes. Allow a cure time of approximately 24 hours, which may vary.
R
Roger DavisAug 22, 2025
Why does my Focus Industries Farm Equipment venturi suck, but not when lines are hooked to the sprayer?
- M
  Michael HartAug 22, 2025
  If the venturi sucks properly until connected to the sprayer, it could be due to improper fittings. Check that all fittings are at least the same size as the hose. Minimize tees and elbows to reduce back pressure. Another common cause is filters in the fill line at the sprayer, which can reduce venturi performance. If your sprayer inlet is 1 1/2” or your tank is smaller than 500 gallons, adapt your Handler to 1 1/2” fittings, preferably by changing the camlock sizes of your 2” Handler to 1 1/2” using reducers and 1 1/2” camlocks, instead of only reducing the hose size.
Y
ymosleyAug 26, 2025
What to do if my Focus Industries Farm Equipment pump is cavitating?
- D
  David FernandezAug 26, 2025
  If the pump is cavitating, reduce suction from the Handler tank by partially closing the suction valve. This will regulate the speed at which the mixture is drawn from the Handler. Once all of the liquid has been drawn from the tank, shut off the suction valve.
D
Daniel ClarkAug 28, 2025
What to do if Focus Industries Handler I suction line is drawing air?
- A
  anna95Aug 28, 2025
  If the suction line is drawing air, reduce suction from the Handler tank by partially closing the suction valve. This will regulate the speed at which the mixture is drawn from the Handler. Once all of the liquid has been drawn from the tank, shut off the suction valve.
A
Ashley BrownAug 30, 2025
What to do if my Focus Industries Farm Equipment jug won’t puncture properly?
- D
  Derek WardAug 30, 2025
  If the jug won’t puncture properly, the blade may be dull. Resharpen the knife assembly by removing it and hand sharpening with a file or grinder.
C
Christy SinghSep 2, 2025
Why is chemical splashing from my Focus Industries Handler I?
- T
  Taylor LangSep 2, 2025
  Chemical splashing can occur due to improper handling of jugs. Apply constant, even pressure when puncturing the container, and avoid forcing the jug onto the knife assembly. A dull blade can also cause splashing, so resharpen the knife assembly by removing it and hand sharpening with a file or grinder.
A
Aaron KellySep 5, 2025
How to fix clogged suction lines or venturi in Focus Industries Handler I Farm Equipment?
- M
  Michael CampbellSep 5, 2025
  If suction lines or the venturi are clogged, especially due to insufficiently dissolved granular product, force water back into the venturi by opening the bypass valve. This allows water to back up into the Handler tank and dislodge any obstructions.
T
Taylor VaughnSep 8, 2025
What to do if the hose is difficult to install on Focus Industries Handler I Farm Equipment?
- B
  Brian HowardSep 8, 2025
  Heat the hose in boiling water until soft. Slide on to hose barb fitting. If necessary, hose lubricants and silicone are available and can be used if compatible.
P
Paul SnyderSep 10, 2025
Why is my Focus Industries Handler I Farm Equipment tank calibration not accurate?
- E
  Emily LucasSep 10, 2025
  Inaccurate tank calibration can result from the tank not being level, so ensure the system is level. It can also be caused by fittings and line volumes not being accounted for. The tank calibration marks indicate the volume of the tank, but do not take into account added volume in the lines and fittings. Pre-calibrate the volume of your lines and fittings to get more accurate readings.