Focusrite Saffire PRO 40 - Saffire PRO 40 Technical Specifications

26
Saffire PRO 40 Specifications
MIC
• Frequency Response: 20Hz - 20kHz +/- 0.1 dB.
• THD+N: 0.001% (measured at 1kHz with a 20Hz/22kHz band pass filter).
• Noise: EIN > 125dB (128dB analogue to digital): measured at ~60dB of gain with 150 Ohm termination
(20Hz/22kHz band pass filter).
LINE
• Frequency Response: 20Hz - 20kHz +/- 0.1dB.
• THD+N: <0.001% (measured with 0dBFS equivalent input and 22Hz/22kHz band pass filter).
• Noise: -90dBu (22Hz/22kHz band pass filter).
INSTRUMENT
• Frequency Response: 20Hz - 20kHz +/- 0.1dB.
• THD+N: 0.004% (measured with 0dBu input and 20Hz/22kHz band pass filter).
• Noise: -87dBu (20Hz/22kHz band pass filter).
DIGITAL PERFORMANCE
• Clock Sources:
Internal clock.
Sync to word clock on S/PDIF (coaxial input).
Sync to word clock on ADAT input.
Sync to word clock on optical S/PDIF input (when enabled).
• A/D Dynamic Range 110dB ‘A-weighted’ (all inputs).
• D/A Dynamic Range 110dB ‘A-weighted’ (all outputs).
• JetPLLTM PLL technology providing superb jitter reduction, for class leading converter performance.
• Clock Jitter < 250 pico seconds.
• Sample rates: 44.1 to 96kHz.
• 20 input channels to computer: Analogue (8), S/PDIF (2), ADAT (8) and Mix Loop-back (2).
• 20 output channels from computer: Analogue (10), S/PDIF (2) and ADAT (8).
• Fully assignable 18 input by 16 output mixer.
WEIGHT and DIMS
• 3kg - 35cm x 4.5cm x 26.5cm.
ANALOGUE INPUTS
• Mic / Line inputs on XLR Combo with auto-switching between XLR and TRS.
• Mic / Line / Instrument 1 & 2: 2 x XLR Combo on front panel.
• Mic / Line 3-8: 6 x XLR Combo.
• Instrument: As above, switched to Instrument (inputs 1 & 2 only).
• Mic Gain: +10dB to + 55dB.
• Line 1-8 Gain: -10dB to +36dB.
• Instrument Gain: +10dB to +55dB.
• Input Pad on inputs 1-2, -9dB.
• Phantom power switched in 4 channel groups on Mic. 1-4 and 5-8.
• Mic and instrument maximum input level +7dBu (+16dBu with pad on inputs 1 and 2).
• Line maximum input level +22dBu.
ANALOGUE OUTPUTS
• Line level 10 x 1/4 inch TRS Jack.
• Outputs Monitor 1 and 2 have anti-thump protection circuitry.
• Nominal output level 0dBFS = 16dBu, balanced.
• Frequency Response: 20Hz – 20kHz +/- 0.2dB.
• THD+N <0.0010% (-100dB) (measured with 0dBFS input 22Hz/22kHz band pass filter, un-weighted).
• Software switched attenuation (–20dB) on outputs 1 and 2 (for sensitive active monitors).
• Hardware and Software Controlled Digital Volume control for all outputs (assignable through control panel).
• Hardware and Software Controlled Digital Dim and Mute controls for all outputs (assignable through control panel).
• All outputs are useable as monitoring outputs