FreeWave FGRO9CSU - Flow Control; Table 7: Flow Control Selections

79 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

FreeWave Technologies Spread Spectrum Transceiver User Manual

900 MHz and 2.4 GHz

V5.0S

24

Flow Control

Use this menu to specify the hardware flow control for the Data port.

Default is 0 (no hardware flow control).

Table 7: Flow control

Selections

Menu Setting Port Notes

0 None Use software control (XON XOFF)

1 RTS

2 DTR

Table of Contents

Default Chapter11
- Table of Contents11
Quick Start15
Quick Start on a Multipoint System16
Tuning Transceiver Performance17
- Table 1: Setup Menu Terminal Settings17
- Figure 1: Initial Menu18
- Figure 2: Freewave Operation Mode Menu19
Operation Mode Selections20
- Point-To-Point Master20
- Point-To-Point Slave20
- Point-To-Multipoint Master20
- Point-To-Multipoint Slave20
- Point-To-Point Slave/Repeater20
- Point-To-Point Repeater21
- Point-To-Point Slave/Master Switchable21
- Table 2: at Script File Commands22
- Figure 3: Using Mode 6 to Call through Repeaters23
- Point-To-Multipoint Repeater24
- (F) Ethernet Options24
Multipoint Operation25
- Theory of Operation25
- Installing Multipoint Systems25
- Overlapping Multipoint Systems26
- Number Repeaters26
- Master Packet Repeat26
- Master Packet Repeat in Multipoint Systems with Repeaters28
- Figure 4: Multipoint Parameters28
- Max Slave Retry29
- Retry Odds29
- Dtr Connect29
- Repeater Frequency29
- Network ID30
- Multimaster Synch30
- PPS Enable/Delay30
- (A) Slave/Repeater31
- (B) Diagnostics31
- (C) Subnet ID31
- Figure 5: Multipoint Subnet Diagram33
- (D) Radio ID34
Baud Rate Selections35
- Set Baud Rate35
- Figure 6: Baud Rate, and Other Items Related to the Data Port35
- Data Word Length and Parity36
- Modbus RTU36
- Rs232/48536
- Table 4: Data Word Length and Parity Selections36
- Setup Port37
- Turnoff Delay37
- Table 5: Data Port Protocol Selections37
- Table 6: Set-Up Port Selections37
- Flow Control38
- Table 7: Flow Control Selections38
Call Book Selections39
- Entering or Modifying Numbers in the Call Book40
- Figure 7: Call Book Menu40
- Programming the Call Book to Use 3 or 4 Repeaters41
- Figure 8: Calling a Slave through 4 Repeaters41
- Programming the Call Book in Multipoint Systems42
Radio Transmission Parameters43
- Figure 9: Radio Parameters Menu43
Radio Statistics54
- Figure 12: Modem Statistics54
Password57
- Setting a Password57
- Changing a Password57
- Disabling a Password58
Transceiver Location59
Front Panel Leds60
- Table 15: LED Status in Point to Point Mode60
- Table 16: LED Status in Multipoint Mode61
Rs232 Pin Assignments62
- Table 17: RS232 Pin Assignments62
Establishing Data Communication Links66
Rs422 & Rs-485 Operation70
- Table 21: RS 485 Half Duplex71
Other Settings72
Technical Specifications73
Troubleshooting77
Oem Board Level Mechanical Drawing79

Related product manuals

Preview: FreeWave FGR2

Preview: FreeWave FGR2-PE

FreeWave FGR2-PE

FreeWave FGR-115RE

FreeWave FGR-115RC

Preview: FreeWave FGR09 Series

FreeWave FGR09 Series