Fuji Electric Micro Control X User Manual

1
2
3
4
5
6
7
1
2
1
2
3
4
5
1
2
3
4
5
Creating a ramp soak operation pattern
Set the following items to create a pattern.
Pattern
Sets which steps to use from the following 15 types.
6WHSVWR6WHSVWR6WHSVWR6WHSVWR6WHSVWR6WHSVWR6WHSV
WR6WHSVWR6WHSVWR6WHSVWR6WHSVWR6WHSVWR6WHSVWR
6WHSVWR6WHSVWR
Target SV Sets the controlled temperature.
Ramp time Sets the time to reach the target SV from the current SV.
Soak time 6HWVWKHWLPHWRPDLQWDLQWKHVSHFL¿HG69
7KHIROORZLQJVWHSVZLOOH[SODLQKRZWRUXQWKHVSHFL¿HGSDWWHUQLQ69WR69
'LVSOD\WKHUDPSVRDNPHQX
").
'LVSOD\SDWWHUQSDUDPHWHU ") and choose pattern 0 (" ").
5XQ69WKURXJK69
'LVSOD\WKHWLPHSDUDPHWHU ") and choose minute:second (" ").
Sets the units of time. Besides minute:second (" "), you can also choose hour:minute
(" ")
'LVSOD\WKHWDUJHWYDOXH ") and set the target temperature.
'LVSOD\WKHUDPSWLPHSDUDPHWHU ") and set the ramp time.
'LVSOD\WKHVRDNWLPHSDUDPHWHU ") and set the soak time.
5HSHDWVWHSVWKURXJKDQGVHWWKHUHPDLQLQJSDUDPHWHUV
Running ramp soak
7KHIROORZLQJVWHSVH[SODLQKRZWRUXQUDPSVRDN
'LVSOD\SURJUDPSDUDPHWHU
DQGFKRRVH581 ").
Ramp soak starts running from the current PV.
Point
Ɣ 7RLQWHUUXSWWKHUDPSVRDNRSHUDWLRQFKRRVH+2/' ") in step 2. To cancel the
LQWHUUXSWLRQFKRRVH581
") again.
Ɣ 
" will display when ramp soak has completed.
*XDUDQW\VRDN
7KLVIXQFWLRQJXDUDQWHHVWKHVRDNWLPH2QO\VRDNWLPHZLWKLQWKHVSHFL¿HGUDQJHRIWHPSHUDWXUHIRU
SV is counted towards soak time.
$VVHHQLQWKH¿JXUHEHORZRQO\WKHVXPRIWKHVKDGHGDUHDVLVFRXQWHGDVVRDNWLPH7KHRSHUDWLRQ
PRYHVRQWRWKHQH[WVWHSZKHQWKHWRWDOVRDNWLPHHTXDOVWKHVSHFL¿HGVRDNWLPH
PV
SV
process value
soak time=T1+T2+T3
guaranty soak
range upper limit
guaranty soak
range lower limit
t
T3T2T1
7KHIROORZLQJVWHSVZLOOH[SODLQKRZWRVHWDQH[DPSOHJXDUDQW\VRDNUDQJHZLWKDQXSSHUOLPLWRI&
and a lower limit of 3°C.
'LVSOD\WKHUDPSVRDNPHQX ").
'LVSOD\JXDUDQW\212))SDUDPHWHU ") and choose on (" ").
'LVSOD\WKHJXDUDQW\VRDN ORZHU OLPLWSDUDPHWHU ") and set the lower limit (in this
H[DPSOHVHWLWWR&
'LVSOD\WKHJXDUDQW\VRDN XSSHU OLPLWSDUDPHWHU ") and set the upper limit (in this
H[DPSOHVHWLWWR&
Press the
key to set the value.
Mode setting
Sets how you want to run ramp soak.
The following items can be set.
Power On Start Ramp Soak starts running from the current PV.
Ending Output Shows the ending output after ramp soak has been completed.
OFF Output Shows the output during OFF after ramp soak has been completed.
Repeat Behavior $IWHU¿QLVKLQJWKHODVWVWHSLQUDPSVRDNWKHSURFHVVVWDUWVDJDLQIURPVWVWHS
Setting Power On Start Ending Output OFF Output Repeat Behavior
“0” Off Continuous control Continuous control Off
“1” Off Continuous control Continuous control On
“2” Off Continuous control Standby Off
“3” Off Continuous control Standby On
³´ Off Standby Continuous control Off
“5” Off Standby Continuous control On
“6” Off Standby Standby Off
³´ Off Standby Standby On
³´ On Continuous control Continuous control Off
“9” On Continuous control Continuous control On
“10” On Continuous control Standby Off
“11” On Continuous control Standby On
“12” On Standby Continuous control Off
“13” On Standby Continuous control On
³´ On Standby Standby Off
“15” On Standby Standby On
PV start
:KHQWKHUDPSVRDNVWDUWV581WKLVIXQFWLRQVHDUFKHVWKH¿UVWSRLQWZKHUHWKHPHDVXUHPHQWYDOXH
(PV) and the program pattern match, and starts operation at that point.
Start of (3)
PV=(1)
PV=(2)
PV=(3)
Start of (2) Start of (1)
SV
,IWKHPHDVXUHPHQWYDOXHGRHVQRWPDWFKWKHSDWWHUQDVZLWK39 WKHQRUPDORSHUDWLRQVWDUWV
7-10. Other Functions
1. Soft start function
When turning on the equipment (including the temperature controller), the soft start function
VXSSUHVVHVWKH09WREHFRPHPD[LPXPRXWSXW,WSODFHVDQXSSHUOLPLWRQ09RXWSXWIRUDVSHFL¿HG
amount of time after power is turned on.
This function is useful for effects such as suppressing the heater output during equipment startup, and
makes load lightened.
$IWHUWKHVSHFL¿HGWLPHKDVSDVVHGDIWHUVZLWFKLQJRQ WKHHTXLSPHQWRULI6)70 WKHVRIWVWDUW
function ends and normal controls begin.
'LVSOD\ Parameter Function
" " (SFo1)
MV1 soft start output set value
Places a limit on MV1 output after power is turned on for a time
period set in SFTM.
" " (SFTM)
Soft start set time
Sets the time for soft start to function after turning power on.
Setting "0" will turn off soft start.
t
control output (MV)
soft start
set time
soft start output
set value
MV when not using
soft start
MV when using
soft start (limited)
power on
0%
Caution
The soft start function cannot be used simultaneously with the dual control
(Be sure to set 0.00 during dual control.)
Point
'XULQJPDQXDOPRGHWKHPDQXDORXWSXWYDOXHKDVSULRULW\EXWVRIWVWDUWZLOOFRQWLQXHWR
keep track of the set time period.
Use the following steps to set soft start output set value and set time.
'LVSOD\WKHVHWXSPHQX
").
'LVSOD\WKHVHWXSPHQX ").
'LVSOD\VRIWVWDUWVHWWLPH ") and set the time.
Press the
key to set the value.
Turn off the power once, and then re-start the controller to begin soft start. (When the soft start
function is turned on, the lower display will alternate showing SoFT and SV.)
1RWH'RQRWXVHDXWRWXQLQJDWWKHVDPHWLPH
PV
SV-1
SV-2
SV-3
SV-4
1st ramp
power on
start
repeats
TM1r TM1S TM2r TM2S TM3r TM3S TM4r TM4S
2nd ramp
4th ramp
3rd ramp
2nd soak
3rd soak
4th soak
1st soak
<RXFDQFKRRVHIURPWKH
following 16 types of modes
according to the combination
of run method options.
- 16 -

Fuji Electric Micro Control X Specifications

General

Brand	Fuji Electric
Model	Micro Control X
Category	Controller
Language	English