What to do if the printer does not print from Fujitsu Notebook?
If the printer isn't printing from your Fujitsu Notebook, first make sure that the printer is switched on and ready for operation. Then, check that the data cable connecting the notebook to the printer is properly connected. Finally, verify whether the correct printer driver is loaded; a faulty, incorrectly installed, or wrong driver can cause printing issues.
What does 'Stuck key' mean on Fujitsu Notebook?
If you are getting a 'Stuck key' error on your Fujitsu Notebook, make sure that no key is pressed.
What does 'Operating system not found' mean on Fujitsu Notebook?
If you receive an 'Operating system not found' error on your Fujitsu Notebook, check in the BIOS Setup to ensure your hard disk has been set correctly and verify that the operating system is installed on the corresponding drive.
How to fix 'Keyboard controller error' on Fujitsu Notebook?
To fix a 'Keyboard controller error' on your Fujitsu Notebook, switch off the notebook using the ON/OFF button. Wait for 3-5 seconds, then switch the notebook back on.
What to do if numerals are written when entering characters on the keyboard of Fujitsu Notebook?
If you're getting numerals instead of characters on your Fujitsu Notebook, it means the virtual number keys are activated. Press the Num button to deactivate them.
What does 'Previous boot incomplete - Default configuration used' mean on a Fujitsu Notebook?
This message means that default values have been set for certain settings due to an error during the previous system boot. Press the F1 function key when prompted to do so.
What does 'Failure Fixed Disk n' mean on Fujitsu Notebook and how can I fix it?
This error indicates that the settings of the hard disk drive are incorrect. Start the BIOS Setup (Primary Master submenu) and select the correct settings.
How to resolve 'Extended memory failed at offset: xxxx' error on Fujitsu Notebook?
This error message indicates that during the extended memory test, an error occurred at the specified address. Check whether the additional memory module has been inserted correctly.
What does 'System CMOS checksum bad - Default configuration used' mean on a Fujitsu Notebook and how to fix it?
This message indicates that the system configuration information is incorrect. To resolve this, switch off the notebook, then switch it back on. Press the F2 function key to access the BIOS Setup. In the BIOS Setup, select the Exit menu, then select 'Load Setup Defaults'. Choose 'OK' and press the Enter key.
What to do if Fujitsu Notebook does not start after switching it on?
If your Fujitsu Notebook doesn't start, there might be a few reasons: * The battery may not be installed correctly, so check if it is properly placed in its compartment. * The battery might be dead, in which case you should charge it, insert a charged battery, or connect the AC adapter. * The AC adapter might not be properly connected; ensure it is securely connected to the notebook.
Essential safety information and precautions to follow when operating the notebook.
Specific safety guidelines for notebooks with wireless LAN and Bluetooth.
Instructions for charging, proper care, and maintenance of the notebook battery.
Step-by-step guide for removing and installing the notebook's rechargeable battery.
Using the fingerprint sensor and Kensington lock for device security.
Setting up passwords for BIOS, OS boot, and hard disk for data security.
Utilizing Trusted Platform Module (TPM) and Smart Card reader for enhanced security.
General precautions for component servicing, including ESD and preparation steps.
Procedures for preparing, removing, and installing memory modules.
Steps for removing and installing the notebook's hard disk drive.
How to access and launch the BIOS Setup Utility.
Navigating and interacting with the BIOS Setup Utility menus.
Options for saving changes, discarding changes, or loading defaults.
General advice, contact info, and steps for recovering the factory image.
Troubleshooting external monitor problems and notebook startup failures.
Resolving printer, wireless, smart card issues, and understanding error messages.
Common wireless LAN connection problems and their solutions.
Steps to create bootable discs, recovery images, and driver backups for Windows 7.
Procedures for recovering the system using various tools and media for Windows 7.
Steps to create a USB recovery drive for Windows 10 troubleshooting.
Overview of options like System Restore and PC Reset for Windows 10.
General| Storage | 256 GB SSD |
|---|---|
| Display | 15.6-inch |
| Graphics | Intel HD Graphics 520 |
| Operating System | Windows 10 Pro |
| RAM | 8 GB |
| Resolution | 1366 x 768 |
| Ports | USB 3.0, HDMI, Ethernet, SD card reader |
| Wireless | Wi-Fi 802.11ac, Bluetooth 4.1 |
| Processor | Intel Core i5-6200U |
To Next Page
