Fujitsu PRIMERGY RX1330 M4 User Manual

Operating Manual RX1330 M4
Content
5 Starting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.1 Installation steps, overview . . . . . . . . . . . . . . . . . . . 58
5.2 Unpacking the server . . . . . . . . . . . . . . . . . . . . . . 60
5.3 Installing the server in the rack . . . . . . . . . . . . . . . . . 61
5.3.1 Installing the server in the rack . . . . . . . . . . . . . . . . . . 63
5.4 Connecting cables . . . . . . . . . . . . . . . . . . . . . . . . 66
5.4.1 Notes on connecting/disconnecting cables . . . . . . . . . . . . 66
5.4.2 Connecting devices to the server . . . . . . . . . . . . . . . . . 67
5.4.3 Connecting the power cord . . . . . . . . . . . . . . . . . . . . 68
5.4.3.1 Using cable ties (standard PSU) . . . . . . . . . . . . . . . 69
5.4.3.2 Using the cable clamp . . . . . . . . . . . . . . . . . . . . . 70
5.5 Switching on the server for the first time . . . . . . . . . . . 71
5.6 Configuring the server with
ServerView Installation Manager . . . . . . . . . . . . . . . . 72
5.6.1 Configuring the server and installing the operating system . . . . 72
5.6.1.1 Configuring the controllers . . . . . . . . . . . . . . . . . . 73
5.6.1.2 Installing the operating system . . . . . . . . . . . . . . . . 73
5.7 Configuring the server without
ServerView Installation Manager . . . . . . . . . . . . . . . . 74
5.7.1 Configuring the server and installing the operating system . . . . 74
5.7.1.1 Configuring the onboard SAS/SATA controller . . . . . . . . 74
5.7.1.2 Installing the operating system . . . . . . . . . . . . . . . . 74
5.8 Notes on configuring controllers . . . . . . . . . . . . . . . . 75
5.8.1 Notes on onboard SATA controllers . . . . . . . . . . . . . . . . 75
5.8.2 Notes on SAS/SATA RAID controllers . . . . . . . . . . . . . . 75
5.9 Note on operating system . . . . . . . . . . . . . . . . . . . 76
6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6.1 Switching the server on and off . . . . . . . . . . . . . . . . 77
6.2 Installing HDD/SSD modules . . . . . . . . . . . . . . . . . . 80
6.2.1 Installing 2.5-inch HDD/SSD modules . . . . . . . . . . . . . . 80
6.2.1.1 Removing a 2.5-inch HDD/SSD dummy module . . . . . . . 80
6.2.1.2 Installing a 2.5-inch HDD/SSD module . . . . . . . . . . . . 81
6.2.2 Installing 3.5-inch HDD modules . . . . . . . . . . . . . . . . . 82
6.2.2.1 Removing a 3.5-inch HDD dummy module . . . . . . . . . . 82

Fujitsu PRIMERGY RX1330 M4 Specifications

General

Chipset	Intel C246
Processor	Intel Pentium, Intel Celeron
Memory Type	DDR4
Memory	Up to 64 GB
Memory Slots	4 DIMM slots
Drive Bays	4 x 3.5-inch or 8 x 2.5-inch
Network	2x 1GbE onboard, optional additional NICs
Power Supply	450W
Form Factor	1U
RAID Controller	optional SAS RAID controller