EasyManuals Logo
Home>Fujitsu>Server>PRIMERGY TX1330 M4

Fujitsu PRIMERGY TX1330 M4 User Manual

Fujitsu PRIMERGY TX1330 M4
110 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #73 background imageLoading...
Page #73 background image
TX1330 M4
Operating Manual 73
Starting up
5.6 Switching the server on for the first time
V CAUTION!
If nothing appears on the screen but flickering stripes after switching
on the server, switch off the server immediately (see chapter
"Troubleshooting and tips" on page 93).
The On/Off button does not disconnect the server from the mains. To
completely disconnect it from the mains, remove the power cords
from the PSUs.
Do not move, strike, or shake the server when it is switched on. This
can damage the HDD/SSD in the server and cause data loss.
Switch the server on when the temperature is in the specified
temperature range. For more information on the operating
environment, see "Ambient conditions" on page 105. When operating
the server out of the specified temperature range, the server may
operate improperly and data loss may occur. Furthermore, Fujitsu
cannot be held responsible for any related damage, malfunction, or
loss of data, etc.
Ensure that you wait for 10 seconds or more after power off before
switching on the server again.
After connecting all power cords, wait at least 10 seconds before
pressing the On/Off button.
Switching the server on
The AC connected indicator lights up green (standby mode) when the server is
connected to the mains.
I It will take about 60 seconds until the server can be switched on.
Starting up
For Japan, see " はじめにお読みください ".
Ê Press the On/Off button.
Ê Configure your server and install the operating system, see section
"Configuring the server with ServerView Installation Manager" on
page 74.

Table of Contents

Other manuals for Fujitsu PRIMERGY TX1330 M4

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu PRIMERGY TX1330 M4 and is the answer not in the manual?

Fujitsu PRIMERGY TX1330 M4 Specifications

General IconGeneral
Chassis typeTower
Product colorBlack
HDD size2.5 \
RAID supportYes
HDD interfaceSerial ATA III, Serial Attached SCSI (SAS)
Optical drive typeDVD±RW
Total storage capacity0 GB
Maximum storage capacity- TB
Number of HDDs installed0
Number of HDDs supported8
Bus typeDMI3
Tjunction100 °C
Scalability1S
Processor cache12 MB
Processor cores6
Processor modelE-2136
System bus rate8 GT/s
Processor socketLGA 1151 (Socket H4)
Processor threads12
Processor codenameCoffee Lake
Processor frequency3.3 GHz
Processor cache typeSmart Cache
Processor lithography14 nm
Processor manufacturerIntel
Processor package size37.5 x 37.5 mm
Processor boost frequency4.5 GHz
Processor operating modes64-bit
Embedded options availableNo
PCI Express configurations1x16, 2x8, 1x8+2x4
Supported instruction setsAVX 2.0, SSE4.1, SSE4.2
Thermal Design Power (TDP)80 W
Number of processors installed1
Maximum number of PCI Express lanes16
Memory types supported by processorDDR4-SDRAM
Memory channels supported by processorDual
Memory clock speeds supported by processor2666 MHz
Memory bandwidth supported by processor (max)41.6 GB/s
Maximum internal memory supported by processor128 GB
Compatible operating systemsMicrosoft Hyper-V Server 2012 R2 Microsoft Hyper-V Server 2016 Microsoft Windows Server 2012 R2 Datacenter Microsoft Windows Server 2016 Datacenter Microsoft Windows Server 2012 R2 Standard Microsoft Windows Server 2016 Standard Microsoft Windows Server 2012 R2 Essentials Microsoft Windows Server 2016 Essentials Microsoft Windows Server 2012 R2 Foundation Microsoft Windows Storage Server 2012 R2 Standard Microsoft Windows Storage Server 2016 Standard Microsoft Hyper-V Server 2012 Microsoft Windows Server 2012 Datacenter Microsoft Windows Server 2012 Standard Microsoft Windows Server 2012 Essentials Microsoft Windows Server 2012 Foundation
Memory slots4
Internal memory16 GB
Maximum internal memory64 GB
LAN controllerIntel i210
Cabling technology10/100/1000Base-T(X)
Ethernet interface typeGigabit Ethernet
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 2 (3.1 Gen 2) Type-C ports quantity2
Power supply450 W
Power supply input frequency50 - 60 Hz
Operating temperature (T-T)5 - 45 °C
Operating relative humidity (H-H)10 - 85 %
CertificationCB, RoHS, WEEE, GS, CE, CSA us, ULc/us, FCC Class A, VCCI:V3 Class A + JIS 61000-3-2, GOST-R, KC, CCC, C-Tick, BSMI
PCI Express slots version3.0
On-board graphics card modelNot available
Processor ARK ID134857
Intel Secure Key Technology version1.00
Weight and Dimensions IconWeight and Dimensions
Depth560 mm
Width177 mm
Height455 mm

Related product manuals