What does it mean if my Fujitsu stylistic R726 is beeping and how to stop it?
If your Fujitsu Tablet is beeping every few seconds, it means the battery is almost dead. To stop the beeping, charge the battery.
Why is the battery of my Fujitsu stylistic R726 discharging too quickly?
If the battery of your Fujitsu Tablet discharges too quickly, it could be due to several reasons. The battery might be too hot or too cold; in this case, the battery indicator flashes, so bring the Tablet PC to a normal operating temperature. If the operating time is extremely short, the battery is likely old and needs replacement. Also, an application running might be consuming excessive power due to frequent hard disk or optical drive access - use the AC adapter whenever possible. Finally, the screen brightness may be set to maximum; reduce it via Control Panel – Hardware and Sounds – Windows Mobility Center to lower energy consumption.
What to do if stylus input is not working on my Fujitsu stylistic R726?
If stylus input isn't working on your Fujitsu Tablet, it could be due to an incorrect driver installation. If your device only operates with a stylus, install the driver for the standard model. If it operates by stylus and finger, install the 'Dual Digitizer' model driver. The stylus may also be in sleep mode; press the upper stylus button to wake it. Finally, the stylus battery might be completely discharged; change it as described in chapters 'Removing the stylus battery', Page 34 and 'Installing the stylus battery', Page 34.
What to do if the battery charging indicator is not lit on my Fujitsu stylistic R726?
If the battery charging indicator is not lit, it means the battery is not being charged. Connect the Tablet PC to a power outlet using the AC adapter. Note that the battery will only be charged again when the battery capacity is less than 90%.
What to do if my Fujitsu stylistic R726 Tablet PC does not start after I switch it on?
If your Fujitsu Tablet PC doesn't start, it could be due to a dead battery. To resolve this, charge the battery or connect the AC adapter to the Tablet PC. Alternatively, the AC adapter might not be properly connected. Ensure it is correctly connected to the Tablet PC and then switch the Tablet PC on.
What to do if the external monitor remains blank when connected to my Fujitsu Tablet?
If the external monitor remains blank, first, ensure the monitor is switched on. If it is, power saving may have been activated, so press a key on the external keyboard or tap the touchscreen. Also, check if the brightness is set too low and adjust it accordingly. The screen output might be set to the Tablet PC touchscreen, so verify the graphics driver settings or whether the external monitor has been detected in 'Intel Graphics Media Accelerator Driver for mobile'. Finally, ensure the AC cable and data cable are properly connected by switching off the Tablet PC and monitor, checking the cable connections, and then switching them back on.
What does the error message 'Press to resume, to SETUP' mean on my Fujitsu Tablet and how do I fix it?
If you receive the error message 'Press to resume, to SETUP' on your Fujitsu Tablet, press the volume up button to start the BIOS Setup, or if you use an external keyboard, press the F1 or F2 key on the keyboard.
What does the error message 'Failure Fixed Disk n' mean on my Fujitsu stylistic R726 Tablet and how do I fix it?
If you receive the error message 'Failure Fixed Disk n' on your Fujitsu Tablet, start the BIOS Setup (Primary Master submenu) and select the correct settings.
How to fix the 'cursor does not correctly follow the stylus movements' issue on a Fujitsu stylistic R726 Tablet?
If the cursor does not correctly follow the stylus movements on your Fujitsu Tablet, it is likely that the stylus is incorrectly calibrated. Calibrate the stylus as described in chapters 'Adjusting the stylus', Page 33 and 'Calibrating the stylus', Page 33.
What to do if I get the error message 'Keyboard controller error' on my Fujitsu stylistic R726?
If you receive the 'Keyboard controller error' message, switch your Fujitsu Tablet PC off using the ON/OFF button. Wait 3-5 seconds, then switch the Tablet PC back on.
Provides essential safety information and references other manuals.
Step-by-step guide to connecting the AC adapter for power.
Instructions for turning the device on for the initial setup.
Steps for turning the Tablet PC on and its power indicator.
Guide to using the stylus for navigation, input, and drawing.
Step-by-step instructions for connecting the Tablet PC to the docking cradle.
Steps for connecting the Tablet PC to the magnetic keyboard.
Steps to configure supervisor and user passwords in the BIOS Setup Utility.
How to set up a password prompt before the operating system starts.
Information on enabling and disabling the TPM security module.
Information on connecting various USB devices, including speeds.
Step-by-step instructions to access the BIOS Setup Utility.
How to navigate, select options, and make changes within the BIOS Utility.
Options for saving changes, discarding changes, or loading defaults before exiting.
Initial steps to take when a fault occurs, including contacting support.
Methods for resetting the device, including forced shutdown.
Guide to creating a recovery drive for troubleshooting and system recovery.
Options for resetting the PC, keeping files or removing everything.
Steps to reinstall Windows using external installation media.
General| Operating System | Windows 10 Pro |
|---|---|
| Bluetooth | Bluetooth 4.1 |
| Display | 1920 x 1080 pixel |
| RAM | 4 GB |
| Storage | 128GB SSD |
| Wireless | 802.11a/b/g/n/ac |
| Ports | USB 3.0, HDMI |
| Card Reader | microSDXC |
| Camera | Front: 2 MP, Rear: 5 MP |
| Security | Fingerprint sensor |
To Next Page