How to fix a keyboard controller error on a Fujitsu stylistic q555 Tablet?
To fix a keyboard controller error on your Fujitsu Tablet, switch your Tablet PC off with the ON/OFF button. Wait 3 - 5 seconds and switch the Tablet PC on again.
Why does my Fujitsu stylistic q555 battery drain so fast?
Your Fujitsu Tablet battery might be draining quickly because it's too hot or cold; in this case, the battery indicator will flash. Bring the Tablet PC to a normal operating temperature. If the battery life is extremely short, the battery is probably too old and needs replacing. Also, an application may be consuming a lot of power by frequently accessing the hard disk or optical drive, so use the AC adapter whenever possible. Finally, the screen brightness might be set too high. Reduce the brightness via Control Panel – Hardware and Sounds – Windows Mobility Center.
What to do if my Fujitsu Tablet PC stops working?
If your Fujitsu Tablet PC stops working, it may be in energy saving mode, so end energy saving mode. An application program may have caused the malfunction, so close the application program or restart the Tablet PC. The battery may also be dead, so charge the battery or connect the AC adapter to the Tablet PC.
What to do if stylus input is not working on Fujitsu Tablet?
If the stylus input is not working on your Fujitsu Tablet, reinstall the driver for the 'dual digitizer'.
How to resolve 'System CMOS checksum bad' on Fujitsu stylistic q555 Tablet?
To resolve the 'System CMOS checksum bad' error on your Fujitsu Tablet, switch the Tablet PC off and then on again. Keep the volume button and the shortcut button pressed while switching it on. If you keep the volume button pressed during the boot process, you can switch into the BIOS Setup. In the BIOS Setup, select the Exit menu, then select the entry Load Setup Defaults, select OK, and press the Enter key.
What to do if I lost Smart Card for Fujitsu Tablet?
If you have lost your user Smart Card, you can continue working with the supervisor Smart Card and initialize a new user Smart Card or deactivate the SystemLock function. If you have lost the supervisor Smart Card, you can also continue working, but you no longer have all rights and cannot initialize another supervisor Smart Card. If you have lost both Smart Cards, you cannot boot your system. Please contact our customer service center. You must provide proof of ownership for the device. The customer service center will then refer you to our service partner, who will unlock your device (for a charge).
Why is the display on my Fujitsu Tablet difficult to read?
If the display on your Fujitsu Tablet is difficult to read, it may be due to reflected glare. Try moving the Tablet PC to a different position. You can also increase the screen brightness.
Why won't my Fujitsu stylistic q555 Tablet print?
If your Fujitsu Tablet isn't printing, first make sure the printer is switched on and ready. Then, check that the data cable between the Tablet PC and the printer is properly connected. Finally, ensure the correct printer driver is loaded; refer to the printer documentation.
What to do with error 'Press to resume, to SETUP' on Fujitsu stylistic q555?
If you see the error message 'Press to resume, to SETUP' on your Fujitsu Tablet, press F1 / Windows button to continue. Alternatively, press F2 / Decrease volume button to enter the BIOS-Setup-Utility.
How to fix wireless connection on Fujitsu stylistic q555?
If the wireless connection on your Fujitsu Tablet isn't working, first ensure the wireless component is switched on. If it is on but the connection still fails, check whether the wireless connection is enabled by the software.
Essential safety information for working with the Tablet PC.
Step-by-step guide to connecting the AC adapter for power.
Procedure for powering on the Tablet PC for initial use and setup.
Steps to power on the Tablet PC and program the ON/OFF button.
Procedures for correctly shutting down the Tablet PC.
Guide to using the stylus for navigation and input.
Describes the docking cradle and its components.
Steps to dock the Tablet PC into the cradle.
Steps for attaching the Tablet PC to the keyboard cover.
Steps to set up and use the fingerprint sensor for security.
Setting up supervisor and user passwords in BIOS Setup Utility.
Enabling system protection via password during boot.
Resolving issues with system startup, recovery, and date/time.
Troubleshooting touchscreen, display readability, and stylus input.
Resolving blank or unstable external monitor displays.
Resolving printer, wireless, and battery discharge problems.
Addressing issues with Smart Card reader, PIN, and lost cards.
Processor, memory, touchscreen, dimensions, and ports of the Tablet PC.
Details on wireless network capabilities, transfer rates, and frequencies.
Details on rechargeable battery and AC adapters.
Details on RF exposure limits, SAR, and testing.
Guides for creating recovery images and restoring the system.
To Next Page
General