19.PARAMETER TABLE
1.7.4.x.3 Safety sub-cooling:
Minimum subcooling value. At this point, the setpoint reduction is stopped.
1.7.4.x.4 Start time:
Logic operating start time.
1.7.4.x.5 End time:
Logic operating end time.
1.7.5.x.1 Operation mode:
Configures the Operation Mode.
0 - Off
1 - Compression
2 - Descompression
1.7.5.x.2 to 1.7.5.x.7 Pressure setpoint 01-06:
Output pressure setpoint 01-06
1.7.5.x.8 to 1.7.5.x.13 Pressure hysteresis 01-06:
Hysteresis of output 01-06
1.7.5.x.14 Pressure sensor:
Specifies the pressure sensor.
1.7.5.1 Individual pressure switches:
The letter x represents individual pressure switches 1 to 3.
Feature
Minimum
Maximum Unit
Standard
Description
1.7.5.x.1
1.7.5.x.7
1.7.5.x.2
1.7.5.x.8
1.7.5.x.3
1.7.5.x.9
1.7.5.x.4
1.7.5.x.10
850,0 (58,6)
0 02
425,0 (29,3)
425,0 (29,3)
425,0 (29,3)
10,0 (0,7)
0
0
0
Psi (Bar)
Psi (Bar)
Psi (Bar)
Psi (Bar)
Psi (Bar)
Psi (Bar)
Psi (Bar)
Psi (Bar)
Psi (Bar)
0
0
0
1.7.5.x.5
1.7.5.x.6
0
0
0
20,0 (1,4)
30,0 (2,1)
40,0 (2,8)
50,0 (3,4)
60,0 (4,1)
10,0 (0,7)
10,0 (0,7)
10,0 (0,7)
850,0 (58,6)
850,0 (58,6)
850,0 (58,6)
850,0 (58,6)
850,0 (58,6)
Pressure setpoint 1
Pressure setpoint 6
Pressure setpoint 5
Pressure setpoint 3
Operation Mode
Pressure setpoint 4
Pressure setpoint 2
Pressure hysteresis 1
Pressure hysteresis 2
Pressure hysteresis 3
1.7.5.x.19
1.7.5.x.14
1.7.5.x.20
1.7.5.x.15
1.7.5.x.21
1.7.5.x.16
1.7.5.x.22
425,0 (29,3)
0 0 -
0
°C (F)
Psi (Bar)
425,0 (29,3) Psi (Bar)
425,0 (29,3) Psi (Bar)
Psi (Bar)
Psi (Bar)
1.7.5.x.13
Psi (Bar)
sec
sec
0 0 -
0 0 -
-
-
-
-
-
-
-
-
-14,8 [off] (-1,1) -14,8 [off] (-1,1)
1.7.5.x.17
1.7.5.x.11
1.7.5.x.23
1.7.5.x.25
1.7.5.x.18
1.7.5.x.12
1.7.5.x.24
0 0 -
0
1 [off]
1 [off]
9999
9999
5
5
0 0 -
0
1 (0,1) 20 (13,8) 1 (0,1)
0
0 0 -
0 0 -
10,0 (0,7)
10,0 (0,7)
10,0 (0,7)
850,0 (58,6)
850,1 [off] (58,7)850,1 [off] (58,7)
Low pressure alarm
Digital output address 6
Digital output address 2
Digital output address 4
Digital output address 5
Digital output address 3
Minimum output on time
Hysteresis of alarms
Minimum time between actuations
High pressure alarm
Pressure hysteresis 5
Pressure hysteresis 4
Pressure sensor
Digital output address 1
Pressure hysteresis 6
Note: If parameters 1.7.4.x.4 and 1.7.4.x.5 are set to OFF, adiabatic
condensation will remain active.
Note: The sensors present in the expansion modules will be listed in
menu 4 after their configuration.
!
Attention: If a dry bulb temperature sensor has been configured for adiabatic condensation, it is not necessary to configure this
parameter.
0 = Not configured
Sensor options:
1 = Base - S1
2 = Base - S2
3 = Base - S3
5 = Base - S5
4 = Base - S4
6 = Base - S6
65
To Next Page
Loading...
Need help?
General
