Abbreviation displayed
on start screen
DL1
DL2
DL3
DT1
DT2
DT3
Abbrevia-
tion used on
setup screen
Abbreviation
displayed on
opening screen
Function name, etc
D/R (D/R) Dual rate function
ATL (ATL) ATL function
EXP-S (EXPS) Steering EXP
EXP-F (EXPF) Throttle EXP (Forward side)
EXP-B (EXPB) Throttle EXP (Brake side)
EXP-3 (EXP3) 3rd Channel brake EXP
EXP-4 (EXP4) 4th Channel brake EXP
SP-TN (SPTn) Steering speed (Turn side)
SP-RN (SPRn) Steering speed (Return side)
AB.P (AB.P) A.B.S. function (Return amount)
ABS.D (ABSD) A.B.S. function (Delay)
CYCLE (CYCL) A.B.S. function (cycle speed)
ACC-F (ACCF) Throttle acceleration (Forward side)
ACC-B (ACCB) Throttle acceleration (Brake side)
ACC-3 (ACC3)
3rd Channel brake acceration
(BRAKE function-ON)
ACC-4 (ACC4)
4th Channel brake acceration
(BRAKE function-ON)
THSP1 (THS1) Throttle speed (ALL/LOW)
THSP2 (THS2) Throttle speed (MID)
THSP3 (THS3) Throttle speed (HIGH)
ST-TR (TRMS) Steering trim
TH-TR (TRMT) Throttle trim
CH3 (3CH) Channel 3
CH4 (4CH) Channel 4
SUBT1 (SBT1) Sub trim (CH1)
SUBT2 (SBT2) Sub trim (CH2)
SUBT3 (SBT3) Sub trim (CH3)
SUBT4 (SBT4) Sub trim (CH4)
IIDLE (IDLE) Idle up function
TLT13 (TL13) Tilt mixing (1>3)
TLT31 (TL31) Tilt mixing (3>1)
PM1-A (PM1A)
Program mixing 1
(RGHT/BRAK/DOWN sides)
PM1-B (PM1B) Program mixing 1 (LEFT/FWRD/UP sides)
PM2-A (PM2A)
Program mixing 2
(RGHT/BRAK/DOWN sides)
PM2-B (PM2B) Program mixing 2 (LEFT/FWRD/UP sides)
B3-RT (B3RT) Brake mixing (3ch brake rate)
B3-DL (B3DL) Brake mixing (3ch delay)
B3ABP (B3AP)
3rd Channel A.B.S -Return amount
(BRAKE function-ON)
B3ABD (B3AD)
3rd Channel A.B.S -Delay
(BRAKE function-ON)
B4-RT (B4RT) Brake mixing (4th brake rate)
B4-DL (B4DL) Brake mixing (4ch delay)
B4ABP (B4AP)
4th Channel A.B.S -Return amount
(BRAKE function-ON)
B4ABD (B4AD)
4th Channel A.B.S -Delay
(BRAKE function-ON)
B34RT (B4AD) Brake mixing (3ch & 4th brake rate)
OFF Not used
Settable functions (DL1/DL2/DL3, DT1/DT2/DT3)
DT2
DT3
DT1
DL1
DL2
DL3
89
Function
Function Select Dial "DIAL"
(Setting range: 1, 2, 5, 10, 20, 30, 40,
50, 100, 2PS)
-Steering trim/throttle trim
When set to the minimum "1", the total
trim operating width is 200 clicks. For
"100", the total operating width is 2 clicks
and for 2PS, the total operating width is
1 click.
-Rate, etc. setting
This is the % value which is operated by
1 click relative to the set value of each
rate. Since the total operating width of
functions having a rate of -100~0~+100
is 200%, when set to "100", the total op-
erating width is 2 clicks. Since the total
operating width of functions with a 0~100
rate is 100%, "100" and 2PS are oper-
ated by 1 click.
-Channel 3/4
When set to the minimum "1", the to-
tal operating width of channel 3 is 200
clicks. For "100", the total operating with
is 2 clicks and 2PS is operated by 1 click.
Relationship between set value
and step amount
To Next Page
Loading...
