GE 040350 - User Manual

Questions and Answers

B
Bonnie WiseAug 14, 2025
What to do if my GE 040350 Portable Generator engine will not start or starts and runs rough?
- T
  Tara KirbyAug 14, 2025
  If your GE Portable Generator engine won't start or runs rough, check the following: ensure the 15 Amp fuse is installed and not blown (install a new one, see System Control Board), replace any blown thermal fuses, ensure the fuel supply is on and not depleted (open fuel valves and check the propane tank), verify the correct fuel selection (check the fuel selector switch), replace a failed battery, or clean or replace a clogged air filter.
R
Ryan HallAug 17, 2025
What to do if my GE 040350 Portable Generator engine is running but there is no AC output?
- J
  Jacob SmithAug 17, 2025
  If your GE Portable Generator's engine runs but has no AC output, possible causes include an open or defective circuit breaker (reset or replace it), a service code in the generator control board (contact a local service facility), or poor wiring connections or a defective transfer switch (check and repair, or contact a local service facility).
T
Timothy GriffinAug 20, 2025
Why does my GE Portable Generator engine run well at no-load but bogs down when loads are connected?
- T
  Trevor AndrewsAug 20, 2025
  If your GE Portable Generator runs well without a load but bogs down when loads are connected, it could be due to several reasons: the generator is overloaded (remove some loads), there's a short circuit in a connected load (disconnect it), there's a shorted generator circuit (contact a local service facility), the fuel pressure or mixture is incorrect (refer to the Gaseous Fuel System section in the installation manual), or the fuel line is kinked (remove the kink or replace the line if necessary).
C
Corey PooleAug 25, 2025
Why does my GE Portable Generator engine shut down during operation?
- L
  linda99Aug 25, 2025
  If your GE Portable Generator engine shuts down during operation, it could be due to a fuel supply issue (check fuel valves and fill the propane tank) or a service code displayed on the control board (refer to the Service Code Detection System).
C
Christopher MillerAug 27, 2025
What to do if there is a loss of power on circuits with my GE Portable Generator?
- S
  Shirley ScottAug 27, 2025
  If you're experiencing a loss of power on circuits with your GE Portable Generator, the generator circuit breaker may be open (reset it). Also, there may be transfer switch problems (consult the transfer switch manual).
J
Julie CarrAug 30, 2025
Why will my GE Portable Generator unit not exercise?
- L
  Lori RossAug 30, 2025
  If your GE Portable Generator unit will not exercise, make sure the control board is set to AUTO (press the AUTO button), the exercise timer is set and not OFF (set the exercise timer), the unit date and time are set (set them), the battery hasn't failed (replace it), and the 15 Amp fuse is present and not blown (install a new one; see System Control Board).
E
Evan ProctorSep 3, 2025
What causes excessive vibration in my GE 040350 Portable Generator?
- E
  Erika RobertsSep 3, 2025
  Excessive vibration in your GE Portable Generator could be caused by a loose mechanical fastener. Check and repair it, or contact a local service facility.
S
Savannah LambertSep 6, 2025
Why is there an odor of fuel coming from my GE 040350?
- M
  Michael JonesSep 6, 2025
  If you notice a fuel odor coming from your GE Portable Generator, it may be due to a fuel leak. Turn off the manual shutoff fuel valve and contact a local service facility.
M
milleramySep 9, 2025
What to do if my GE Portable Generator unit does not stop when utility power returns?
- E
  Emily OliverSep 9, 2025
  If your GE Portable Generator unit doesn't stop when utility power returns, it could be due to blown fuses in the transfer switch (install new fuses), the 5-minute minimum runtime not having elapsed (wait 5 minutes), or a poor wire connection or defective controllers (check, repair, or contact a local service facility).