Care and cleaning of the range,
Burner cap is Burner cap is
properly seated. NOTproperly
seated.
Burner heads (onSome models)
The burner heads (on sOmemOdels)
are removable: Simply lift them off
Tri-ring head(on some models)
Burnerhead
)
Burnerbase
Make Suretheringintheburnerhead
ispositionedovertheelectrodeand
thatthe burner head isfully inserted
insidethe burnerbase.A smallgap
between the baseand headis normal.
Front-right head (on s0me modeis),
front-left head, back-right head and
baCk:left head
Stability nber useasewing
_i_ needleort_vistTtie
Burner(k._ -_,,_..)) tounclogthe
• "_'_ smallholeinthe
has_ Electrode burnerhead:
Make Surethe Slotin the burner head
iSpositioned Overthe electrode,
Hole in
head
Theovalburnerhead/capassemblyis
removable_Simplyliftit Offtherangefor
cleaning usea sewingneed!eor twistTtie
to Unclogthe smallholeinthe burner
heads,
34
Burner Caps, Bases and Heads
Beforeremovingthe burner capsand heads(on
some models),remembertheir sizeand location.
Replacethem inthe same location after cleaning.
NOTE: Do not use steel wool or scouring
powders to clean the burner parts.
Burner caps
Lift off when cool.Wash burner caps in hot,
soapy water and rinsewith clean water. You
may scour with a plastic scouring pad to
remove burned-on food particles.Toget rid of
burned on food, place the caps in a covered
container. Add 1/4 cup ammonia and let soak
for several hours or over night. Wash, rinsewell
and dry.
Tri-ring burner (onsome models)
Theouter cap on the tri-ring burner isnot
removable.Onlythe center round capmay be
removed for cleaning.
Tocleanthe burnerbases,usesoapywater anda
plasticscouringpad.Wipecleanwith a dampcloth.
Makesure that no water gets into the burner
bases.Allowthem to dry fully before using.
Burner Heads (on some models) and Oval
(Center) Burner Head/Cap Assembly
The burner heads and the oval burner head/cap
assembly are removable. Simply lift them off the
range for cleaning.
For proper ignition, make sure the small hole in
the section that fits over the electrode is kept
open. A sewing needle or wire twist-tie works
well to unclog it.
The slits in the burner heads must be kept clean
at all times for an even, unhampered flame.
Clogged or dirty burner ports or electrodes will
not allow the burner to operate properly.
Any spillon or around an electrode must
be carefully cleaned. Take care to not hit an
electrode with anything hard or it could be
damaged.
Clean the burner heads routinely, especially
after bad spillovers, which could clog the
openings. Liftoff when cool.
To remove burned-on food, soak the burner
heads in a solution of mild liquid detergent
and hot water for 20-30 minutes. For more
stubborn stains, use a toothbrush.
After cleaning
Beforeputting the burner caps,heads(onsome
models)and ovalhead/cap assemblyback,shake
out excesswater and then drythem thoroughly
bysettingin a warm oven for 30 minutes.
Replacement Burner Heads (onsome models)
Replaceburner heads overthe electrodes on
the cooktop, inthe correct locations according
to their size.Thereisone small,one medium,
one large and one extra-large burner head.
Front of range
-_ ,,
'onsomemoae_s
Trl-rln ] neaa
Makesuretheslotor no_edependingonmodel
tneournerheadispositionedovertneelectroae.
_S at or
E ectr
4ole
:troae
Oval (CentedBurner Head/Cap Assembly
ReD,acemeova center)neaa/caDassemD_yover
theelectrodeonmeCOOKtOp.
Ovai neaaand cad
assemE.,
0
Front of ranoe
MaKe sure 1:hesic t in l:ne
burner heac [s oositioned
over _ne electrode.
°/
Elec_roae
Caps
Reo,acethematchingsizeCaDSontomeburner
Dosesorheads
Hakesurethatthe headson somemodelsana
capsarereplacedin tnecorrectlocatlons
0
. o
. i__ _om e models)
Front of range Trl-nng caF
on some models
To Next Page
Loading...
