GE AV-300I - Page 6

1.4.5.3 Manual Tuning of the Flux Regulator ...................................................................................... 55
1.4.5.4 Manual Tuning of the Speed Regulator ..................................................................................57
1.5 Command Configuration (I/O CONFIG) ...........................................................................................59
1.5.1 Definition of the Commands ....................................................................................................59
1.5.2 Command Block (Commands) ................................................................................................ 60
1.5.2.1 Enable/Disable Control Function ............................................................................................. 62
1.5.3 Typical Command Configurations ............................................................................................62
1.5.3.1 Control from Keyboard/Display Module (Factory Setting) .....................................................62
1.5.3.2 Control from Remote Pushbuttons ......................................................................................... 63
1.5.3.3 Control from a LAN, Usage of Fast Stop ...............................................................................64
1.5.4 Unmanned Installation ...........................................................................................................64
1.6 Configuration of the Analog and Digital Inputs/Outputs (I/O CONFIG) ............................................. 66
1.6.1 Analog Input Block (Analog Inputs) .......................................................................................... 66
1.6.2 Analog Input Block for 1x and 2x Expansion Cards (Exp Analog Inputs 1X & 2X)......................69
1.6.3 Analog Output Block (Analog Outputs) .................................................................................... 71
1.6.4 Digital Input Block (Digital Inputs) ............................................................................................ 72
1.6.5 Digital Output Block (Digital Outputs) ...................................................................................... 75
1.6.5.1 Configuration of the OK Relay (Terminals 80, 82) ................................................................... 77
1.6.6 Word Composing and Decomposing Block (Bits->Word & Word->Bits)................................ 77
1.6.7 Forward and Reverse Control Block (Fwd Rev Ctrl) ................................................................ 81
1.7 Ramp Configuration (RAMP CONFIG) ............................................................................................. 83
1.7.1 Ramp Setpoint Block (Ramp Setpoint) ..................................................................................... 83
1.7.2 Multi Ramp Block (Multi Ramp) ...............................................................................................85
1.7.3 Ramp Block (Ramp Function) ................................................................................................... 88
1.8 Speed Configurations (SPEED CONFIG) ........................................................................................... 90
1.8.1 Speed Setpoint Block and Speed Ratio Block (Speed Setpoint & Speed Ratio) ......................... 90
1.8.1.1 Example: Rubber Calender...................................................................................................... 92
1.8.2 Speed Regulation Block (Spd reg Function) ..............................................................................93
1.8.3 Jog Function Block (Jog) .........................................................................................................95
1.8.4 Multi Speed Block (Multi Speed) ............................................................................................. 97
1.8.5 Motopotentiometer Block (Moto Pot) ....................................................................................... 99
1.8.6 Speed Zero Control Block (Spd 0 Logic) ................................................................................101
1.8.7 Speed Regulator Gain Profile Block (Speed Gain Profile) ........................................................103
1.8.8 Droop Block “Current scale” (Speed Droop) ..........................................................................106
1.8.9 Speed Feedback Derivative Block “Speed Up” (Spd Fbk Deriv)............................................. 107
1.8.10 Inertia and Friction Compensation Block (Inertia / Frict cp)...................................................108
1.9 Torque Current Configurations (TORQUE CONFIG) .........................................................................110
1.9.1 Block Generating the Torque Setpoint, the Torque Current Limit Control and the Zero Torque.
(Torque Setpoint - Torque Curr Lim - Zero Torque Cmd) ..............................................................110
1.9.2 DC Link Voltage Control (VdcCtrl Reg - Max Regen Power) .....................................................114
1.10 Flux Current Configurations (FLUX CONFIG) ...............................................................................115
1.10.1 Control of the Flux Current Maximum Limit (Flux Max Limit) .................................................115
1.10.2 Control of the Magnetizing Current (Magnetiz Config)...........................................................115
1.10.3 Output Voltage Control (Output Vlt Ref)................................................................................. 116