24 
  NX-6V2 Control 
  70  AUX POWER OVERCURRENT / RESTORE COMM CODE  4 ............ numerical 
Location 70 contains the digits for a 4+2 format that will be sent if "Aux Power Overcurrent Reporting" is enabled.  Segments 1 & 2 
contain the digits of the "Aux Power Overcurrent Reporting".  Segments 3 & 4 contain the digits of the "Aux Power Overcurrent 
Restore".  (Box on pg 23.) 
 
  71  BELL TAMPER / RESTORE COMMUNICATOR CODE  4 ............ numerical 
Location 71 contains the digits for a 4+2 format that will be sent if siren supervision reporting is enabled. Segments 1 & 2 contain the 
digits of the "Bell Tamper Reporting".  Segments 3 & 4 contain the digits of the "Bell Tamper Restore".  (Box on pg 23.) 
 
  72  TELEPHONE LINE CUT / RESTORE COMM CODE   4 ............ numerical 
Location 72 contains the digits for a 4+2 format that will be sent if "Telephone Line Cut Reporting" is enabled. Segments 1 & 2 contain 
the digits of the "Telephone Line Cut Reporting".  Segments 3 & 4 contain the digits of the "Telephone Line Cut Restore".  (Box on pg 
23.) 
 
  73  GROUND FAULT / RESTORE COMMUNICATOR CODE  4 ............ numerical 
Location 73 contains the digits for a 4+2 format that will be sent if "Ground Fault Reporting" is enabled, and the NX-870E is installed. 
Segments 1 & 2 contain the digits of the "Ground Fault Reporting".  Segments 3 & 4 contain the digits of the "Ground Fault Restore".  
(Box on pg 23.) 
 
  74  EXPANDER TROUBLE / RESTORE COMM CODE  4 ............ numerical 
Location 74 contains the digits for a 4+2 format that will be sent if "Expander Trouble Reporting" is enabled.  Segments 1 & 2 contain 
the digits of the "Expander Trouble Reporting".  Segments 3 & 4 contain the digits of the "Expander Trouble Restore".  (Box on pg 23.) 
 
  75  FAIL TO COMMUNICATE COMMUNICATOR CODE  2 ............ numerical   
Location 75 contains the digits for a 4+2 format that will be sent if the "Fail To Communicate Reporting" is enabled.  (Box on pg 23.) 
 
  76  LOG FULL COMMUNICATOR CODE  2 ............ numerical 
Location 76 contains the digits for a 4+2 format if the "Log Full Reporting" is enabled.  (Box on pg 23.) 
 
 77  OPENING COMMUNICATOR CODE  2 ............ numerical 
Location 77 contains the digit of a 4+2 format if the "Opening Reporting" is enabled. (Box on pg 23.) 
Segment 1 = Partition 1 Segment 2 = Partition 2   
 
 78  CLOSING COMMUNICATOR CODE  2 ............ numerical  
Location 78 contains the digit of a 4+2 format if the "Closing Reporting" is enabled. (Box on pg 23.) 
Segment 1 = Partition 1 Segment 2 = Partition 2   
 
  79  AUTOTEST COMMUNICATOR CODE  2 ............ numerical  
Location 79 contains the digits for a 4+2 format that will be sent if the "Autotest" or "Manual Test" is enabled. (Box on pg 23.) 
 
  80  RECENT CLOSING & EXIT ERROR COMM CODE  2 ............ numerical 
Location 80 contains the digits for a 4+2 format that will be sent if "Recent Closing" and/or "Exit Error Reporting" is enabled.  Segment 
1 contains the digit for the "Recent Closing Reporting".  Segment 2 contains the digit for the "Exit Error Reporting".  (Box on pg 23.) 
 
  81  START PROGRAM & END PROGRAM COMM CODES  4 ............ numerical 
Location 81 contains the digits for a 4+2 format that will be sent if "Start / End Programming Reporting" is enabled.  Segment 1 
contains the digit for the "Start Program Reporting".  Segment 2 contains the digit for the "Start Program Reporting".  Segment 3 
contains the digit for the "End Program Reporting".  Segment 4 contains the digit for the "End Program Reporting".  (Box on pg 23.) 
 
  82  END DOWNLOAD COMMUNICATOR CODE  4 ............ numerical  
Location 82 contains the digits for a 4+2 format that will be sent if "End Downloading Reporting" is enabled.  Segments 1 and 2 are 
Reserved.  Segment 3 contains the digit of the "End Download Reporting".  Segment 4 contains the digit of the "End Download 
Reporting". (Box on pg 23.)   Note: A start download report will be sent to the internal event log.  
 
  83  CANCEL COMMUNICATOR CODE  1 ............ numerical 
Location 83 contains the digit for a 4+2 format that will be sent if "Cancel Reporting" is enabled. Segment 1 contains the digit for the 
"Cancel Communicator Reporting". (Box on pg 23.) 
 
 84-87 RESERVED