Gesipa AccuBird Pro - User Manual

Other manuals for Gesipa AccuBird Pro

Operating Manual With Spare Parts List15 pages

Questions and Answers

M
martinrobertAug 14, 2025
What to do if my Gesipa AccuBird Pro have no spent mandrel discharge?
- C
  Christopher ConnerAug 14, 2025
  If your Gesipa Rivet Tool isn't discharging spent mandrels, several factors could be at play. First, the nosepiece might be too small; exchange it according to the table. Second, there might be dirt inside the head, so cleaning it is essential. Third, the spent mandrel container might be full, requiring you to take it off and empty it. Lastly, the mandrel tube could be blocked; remove the blocked mandrel and check for free ejection.
A
Angela WangAug 17, 2025
Why my Gesipa AccuBird Pro cannot set blind rivet?
- D
  David CobbAug 17, 2025
  If your Gesipa Rivet Tool is unable to set blind rivets, the following reasons may apply: * The battery may be depleted. Charge or replace the battery if necessary. * The jaws may be dirty or worn. Clean and lubricate or grease the sliding surfaces, or replace them. * The jaw assembly may be loose. Tighten the jaw assembly.
A
Amy PatrickAug 21, 2025
How to fix Gesipa Rivet Tools blocked on return?
- L
  Laura BrownAug 21, 2025
  If your Gesipa Rivet Tool is blocked on return, unscrew the steel head sleeve and remove the blockage.
R
Roger HeathAug 25, 2025
What to do if Gesipa Tools blind rivet cannot be set?
- J
  Julie EllisonAug 26, 2025
  If a blind rivet cannot be set using Gesipa Tools, it may be due to several reasons. First, check the battery charge and replace it if necessary. Second, the jaws might be dirty or worn. In this case, clean and lubricate or grease the sliding surfaces, or replace the jaws. Third, the jaw assembly could be loose, so tighten it.
C
Christina HuffmanAug 28, 2025
Why are the LED lights flashing on my Gesipa Tools?
- J
  Julia GrossAug 28, 2025
  If the LED lights are flashing on your Gesipa Tools, it could indicate a few issues. One potential cause is a low battery, so try changing the battery. Another reason could be that the blind riveting tool is overloaded. If the LED flashes slowly (1 Hz), select rivet dimensions according to work capacity. Alternatively, the tool might be blocked on return, indicated by the LED flashing fast (2 Hz). If this happens, unscrew the steel head sleeve and remove the blockage.
R
Rebecca HoffmanSep 1, 2025
What to do if there is no spent mandrel discharge from Gesipa Tools?
- B
  brian11Sep 2, 2025
  If there is no spent mandrel discharge from Gesipa Tools, consider the following possibilities: * The nosepiece may be too small, so exchange it according to the table. * There might be dirt inside the head, so clean it. * The spent mandrel container could be full; take it off and empty it. * The mandrel tube might be blocked; remove the blocked mandrel and check for free ejection.
S
Samuel RodriguezSep 5, 2025
Why is my Gesipa Power Tool not setting blind rivets?
- R
  Richard VillarrealSep 5, 2025
  If your Gesipa Power Tool is not setting blind rivets, the possible causes include a depleted battery (charge or replace it), dirty or worn jaws (clean and lubricate, or replace them), or a loose jaw assembly (tighten it).
U
udominguezSep 9, 2025
What to do if my Gesipa Power Tool has no spent mandrel discharge?
- M
  Michael SimmonsSep 9, 2025
  If your Gesipa Power Tool isn't discharging spent mandrels, consider these potential issues: the nosepiece may be too small (exchange it according to the table), there could be dirt inside the head (clean it), the spent mandrel container might be full (empty it), or the mandrel tube could be blocked (remove the blocked mandrel and check for free ejection).