Gesipa taurus 2 - User Manual

Other manuals for Gesipa taurus 2

User Manual6 pages

Repair Instructions12 pages

Operating Instructions90 pages

Operating Manual With Spare Parts List12 pages

Questions and Answers

L
Logan MillerAug 4, 2025
What to do if Gesipa taurus 2 Rivet Tools blind rivet is not set?
- A
  Angela HallAug 4, 2025
  If the blind rivet is not set, the issue might be due to several reasons. The jaws could be dirty; in this case, clean and oil the sliding surfaces. Alternatively, the jaws might be worn, requiring replacement. Insufficient working pressure could also be the cause, so check the working pressure. Finally, the tool stroke might be too low, which can be resolved by topping up with hydraulic oil.
H
Heather EvansAug 8, 2025
Why is the spent mandrel not evacuated from my Gesipa taurus 2 Rivet Tools?
- S
  Samantha HubbardAug 8, 2025
  If the spent mandrel is not being evacuated, there could be several reasons: * The spent mandrel container might be full, so you should empty it. * The wrong nosepiece might be in use; replace it according to the table. * The nosepiece might be worn, in which case you should replace it. * The spent mandrel might be jammed in the jaws; clean the jaws and jaw housing and oil the sliding surfaces, replacing them if worn.
S
Susan TrevinoAug 12, 2025
What to do if spent mandrel is not evacuated from my Gesipa taurus 2 Rivet Tools?
- C
  Courtney HallAug 12, 2025
  If the spent mandrel is not evacuated, several factors could be at play. First, check if the spent mandrel container is full and empty it. Ensure that you are using the correct nosepiece; if not, replace it according to the table. A worn nosepiece can also cause this issue, so replace it if necessary. Lastly, the spent mandrel might be jammed in the jaws. In this case, clean the jaws and jaw housing, oil the sliding surfaces, and replace the jaws if they are worn.
C
Christian MurrayAug 17, 2025
Why is the blind rivet not set with my Gesipa taurus 2?
- B
  Brett HarrisAug 17, 2025
  If the blind rivet is not set, several issues could be the cause. The jaws might be dirty, so clean and oil the sliding surfaces. Alternatively, the jaws could be worn, requiring replacement. Insufficient working pressure could also be the problem; refer to the working pressure guidelines. If the tool stroke is too low, top up with hydraulic oil. Also, check the positioning of the steel head sleeve.
H
hmillerAug 21, 2025
What to do if Gesipa Power Tools blind rivet is not set?
- K
  Kenneth ReynoldsAug 21, 2025
  If the blind rivet is not set, several factors could be at play. The jaws might be dirty, in which case you should clean and oil the sliding surfaces. Alternatively, the jaws could be worn and need replacement. Insufficient working pressure could also be the cause, so check the working pressure. Finally, the tool stroke might be too low, requiring you to top up with hydraulic oil.
L
Luke BernardAug 26, 2025
Why does my Gesipa Rivet Tools reload more than one rivet?
- C
  christopherbenjaminAug 26, 2025
  If your Gesipa Rivet Tools reload more than one rivet, this could be due to dirty or worn jaws. Try cleaning and oiling the sliding surfaces, or replacing the jaws.
A
Adam JohnsonAug 30, 2025
What to do if speed rivet cannot be set with Gesipa Rivet Tools?
- Q
  qschroederAug 30, 2025
  If you cannot set a speed rivet with your Gesipa Rivet Tools, several factors could be at play. The jaws might be dirty, requiring cleaning and greasing of the sliding surfaces. Alternatively, the jaws may be worn and need replacement. Insufficient working pressure could also be the cause, so check the working pressure. A low gun stroke may require filling with hydraulic oil. Finally, ensure the white valve is activated to shut the jaws.

Summary

Correct Use

Safety Instructions

Work Capacity

Technical Data

Assignment of Spreader Nosepieces and Mandrel Springs

Spreader Nosepiece Without Opening Mechanism

Spreader Nosepiece With Opening Mechanism

Starting Procedure

How to Set a Speed Rivet

Guides the user through connecting the tool and setting rivets.

How to Reload the Rivet Setting Tool

Maintenance and Care

Cleaning;Changing Jaws

Refilling Hydraulic Oil

Repairs

Troubleshooting

Speed Rivet Cannot Be Set

Identifies causes and remedies for when a speed rivet fails to set.

Not Possible to Reload the Speed Rivet

Troubleshooting steps for issues preventing rivet reloading.

Rivet Setting Tool Reloads More Than One Rivet

Addresses problems where the tool reloads multiple rivets at once.

Gesipa taurus 2 Specifications

General

Working Pressure	5-7 bar
Rivet Diameter Range	2.4-4.8 mm
Traction Power	10, 000 N
Rivet Diameter (Aluminum)	2.4-4.8 mm
Rivet Diameter (Steel)	2.4-4.8 mm
Rivet Diameter (Stainless steel)	2.4-4.8 mm
Type	Pneumatic