What to do if the temperature in the chamber of Getinge Laboratory Equipment is too low?
If the temperature in the chamber of the Getinge Laboratory Equipment is too low, you should: 1. Check that there is power on all phases up to the elements. 2. Check that the unit is not damaged.
What to do if there is low disinfection temperature in Getinge WD15 CLARO?
If there is a low disinfection temperature in the Getinge Laboratory Equipment, you should: 1. Check that there is power on all phases up to the elements. 2. Check the calibration of the temperature sensors.
What to do if there is low temperature in dryer of Getinge Laboratory Equipment?
If there is a low temperature in the dryer of the Getinge Laboratory Equipment, you should: 1. Check there is power to the unit. 2. Replace the temperature switch.
General| Type | Washer-disinfector |
|---|---|
| Cleaning Performance | Complies with EN ISO 15883 |
| Power Supply | 230V, 50/60Hz |
| Washing levels | 2 levels |
| Temperature Range | Up to 93°C |
| Programs | Multiple programmable cycles |
| Water Consumption | Approx. 15 L per cycle |
| Control System | Microprocessor-controlled with touch panel |
| Application | Cleaning and disinfection of laboratory glassware and utensils |
Explains symbols used for warnings and hazards in the manual.
Lists crucial safety and operational guidelines for users.
Specifies the need for a lockable isolating device for the machine's power supply.
Outlines emergency actions like switching off the main switch and closing valves.
Defines the machine's purpose and fields of application.
Describes general functionality and accessories.
Details buttons, indicators, and their functions.
Explains standard and optional dosing systems for detergents and rinse-aid.
Important checks for detergent flow, recalibration, and handling.
Specifies salt type, container capacity, and usage.
Details steps for filling the salt container.
Warning about running a process to remove salt residue after long non-use.
Conditions and procedure for opening the door.
Guidelines for loading items onto the trolley and into the machine.
Methods for choosing and confirming a program.
Need for a fine filter to prevent blockages.
Explains results of interrupting an active program.
Visual cues and door unlocking upon completion.
Warning to handle items carefully due to heat.
Emphasizes complete emptying to prevent cross-contamination.
Rules for loading to ensure water reach and prevent blockages.
How to load sharp utensils, vessels, and endoscopes.
Lists incompatible materials and endoscope preparation.
Emptying acids, solvents, etc., before washing.
Safe handling and recalibration for new detergents.
Follow instructions, avoid domestic types, handle chemicals safely.
Check for objects, spray arms rotation, and strainers.
Verify levels in containers and trolley dockings.
Visual inspection of accessories and cleaning outcomes.
Daily check of spray arm journal and cleaning bellows.
Steps for removing, cleaning, and re-installing spray arms.
Removing limescale using a descaling program.
Cleaning exterior surfaces and control panel.
Location and use of the test port for validation purposes.
Notes on changing parameters and reference to Technical manual.
Illustration of a program printout with a printer.
Explanation of how handling alarms appear on the screen.
Details on low detergent/salt level alarms.
Clarification on detergent alarms allowing partial completion.
How error codes are shown when the red lamp is active.
Steps to acknowledge, enter password, and unlock.
Warning about items not being clean and needing re-washing.
List of error codes (A00, A01, etc.) and their meanings.
Step-by-step guide for paper roll replacement.
Machine tested with Getinge detergents per EN ISO 15883.
Usage of chemicals and manufacturer's liability.
Compatibility of detergents with materials.
Table showing detergents and compatible hose materials.
Why water quality affects cleaning and disinfection.
Impact of hardness, ions, microbes, and chemicals.
Typical parameters for RO water quality.
No household waste, disinfect before recycling.
Taking machines to recycling plants, proper sorting.
To Next Page
