What to do if my GIRBAU Washer ends with END/BAL report?
If your GIRBAU Washer displays 'END/BAL' at the end of a wash cycle, try unloading and reloading the machine. Then, restart the wash cycle, advancing the program to its last phase to repeat the spin cycle without refilling water. If the issue continues, contact the Authorised Technical Service.
Why is my GIRBAU Washer leaking water inside the cabinet?
If you notice water leaking inside the GIRBAU Washer cabinet, first, check the outlet draining pipe. Next, inspect the seals on the water inlet hoses and tighten the connection couplings. Also, examine the door seal for ruptures. If the leak persists, seal all water inlets and then contact the Authorised Technical Service.
How to fix a strange noise during spin cycle in GIRBAU Washer?
If your GIRBAU Washer is making a strange noise during the spin cycle, check the machine's levelling according to the Installation Instructions. Then, tighten the locking screws on the outside panels. If the noise continues, contact the Authorised Technical Service.
What to do if my GIRBAU Washer door is leaking?
If the door of your GIRBAU Washer is leaking, clean the door seal to remove any deposits or linen remains.
What does ALM/HOT mean on my GIRBAU Washer?
If your GIRBAU Washer displays the error 'ALM/HOT', close the washer door to allow the cold water valve to open. Press the START/STOP key to drain the bath and access the door opening. Repeat this until the alarm disappears. If it persists after five attempts, disconnect the power supply and close the water inlet valves, then contact AUTHORISED TECHNICAL SERVICES.
Why won't my GIRBAU Washer door unlock when it says 'Hot'?
If the program is interrupted using the START/STOP key while the bath is at a high temperature, the GIRBAU Washer will automatically accept cold water and will not allow the door to unlock. When the bath temperature is below 45 ºC (133 ºF) the bath will drain and the safety door lock will be released.
What does error ALM/A-* mean on my GIRBAU Washer?
If your GIRBAU Washer shows 'ALM/A-*', check the water entry pressure, the manual water inlet valves, and the filters in the solenoid valves. Refer to section 10: Maintenance.
What to do if my GIRBAU Washer says 'door'?
If the GIRBAU Washer displays a 'door' error, open and close the door properly.
Essential precautions to reduce risk of fire, electric shock, or injury.
Guidelines for correct operation, maintenance, and preservation of the machine.
Details the models to which this manual applies.
Defines the machine's purpose and prohibited uses.
Describes the physical and mechanical features of the washer.
Explains the built-in safety mechanisms of the washer.
Covers selecting, programming, and executing wash programs.
Allows personalization of operation and program settings.
Identifies and explains the controls on the LOGI CONTROL panel.
Identifies and explains the controls on the LOGI PRO CONTROL panel.
Details methods for stopping program execution, including emergency stop.
Provides guidance on proper loading techniques for optimal results.
Step-by-step guide on how to select and start a wash program.
Explains the symbols and options used in the program tables.
Details default program settings for various applications.
Lists the available menus within the Advanced Use Mode.
Instructions on how to enter the Advanced Use Mode.
Details how to customize wash programs within the Pro menu.
Guides users through changing operational parameters.
Instructions for managing the access code.
Explains symbols and options in LOGI PRO program tables.
Details default programs for various applications in LOGI PRO.
Lists available menus for LOGI PRO Advanced Mode.
Instructions for entering LOGI PRO Advanced Mode.
Details customizing LOGI PRO wash programs.
Guides users through changing LOGI PRO operational parameters.
Instructions for managing the LOGI PRO access code.
Procedure for safely freeing trapped persons or animals from the washer.
Steps for manually releasing the door safety lock mechanism.
Addresses common issues like cycle end reports, noises, and leaks.
Lists display reports, likely causes, and procedures for system alarms.
User-performed maintenance tasks like cleaning the washer and door seal.
Procedure for cleaning solenoid valve filters, requiring qualified personnel.
Procedures for checking the door lock and emergency stop functions.
Steps for cleaning front and top dispenser types.
Recommended periodic professional servicing and checks.
Steps for safely disconnecting and preparing the machine for removal.
Information on machine components and material recycling.
General| Languages | Multiple languages supported |
|---|---|
| Compatibility | Girbau industrial laundry machines |
| Programs | Multiple customizable programs |
| Connectivity | Ethernet, USB |
| Display | LCD display with clear information presentation |
To Next Page
