Graco Husky 2200 User Manual (English)

Other manuals for Graco Husky 2200

Operation24 pages

Repair Parts34 pages

Operating Instructions24 pages

Questions and Answers:

D
davidhillAug 21, 2025
How to fix a Graco Water Pump that cycles but won't prime?
- M
  Michael WilliamsAug 21, 2025
  If your Graco Water Pump cycles but won't prime, first try reducing the air inlet pressure, as the pump might be running too fast, causing cavitation. Also, inspect the check valve ball for wear or obstructions and replace the ball and seat if necessary. Check the seat for wear and replace the ball and seat. Ensure that the outlet and inlet are not clogged; unclog them if necessary. Make sure the inlet and outlet valves are open, and tighten any loose inlet fittings or manifolds. Replace any damaged manifold o-rings.
R
Ross CampbellAug 23, 2025
How to fix Graco Husky 2200 leaking air externally?
- M
  megan21Aug 23, 2025
  If your Graco Water Pump is leaking air externally, ensure that the air valve or fluid cover screws are tightened. If the diaphragm is damaged, replace it. Also, replace the air valve gasket if it is damaged.
W
William JohnsonAug 25, 2025
What to do if my Graco Husky 2200 has air bubbles in the fluid?
- J
  Jason RuizAug 26, 2025
  If you notice air bubbles in the fluid, several issues could be the cause. First, check if the suction line is loose and tighten it. A ruptured diaphragm could also be the culprit, so consider replacing it. Inspect manifolds, seats, and o-rings for looseness or damage; tighten manifold bolts or replace seats or o-rings as needed. Pump cavitation might be happening, so reduce the pump speed or suction lift. Finally, ensure the diaphragm shaft bolt is tightened.
M
Mark ThompsonAug 26, 2025
Why does my Graco Husky 2200 cycle but not prime?
- M
  Molly DiazAug 27, 2025
  Several factors can cause a Graco Water Pump to cycle without priming. The pump might be running too fast, leading to cavitation; reduce the air inlet pressure to resolve this. Inspect the check valve ball for wear or if it's wedged, and replace the ball and seat if necessary. Also, a worn seat can cause this issue, so replace the ball and seat. Check for clogs in the outlet or inlet and unclog them. Ensure the inlet or outlet valve is open, and tighten any loose inlet fittings or manifolds. Lastly, inspect manifold o-rings for damage and replace them if needed.
C
Christine SmithAug 28, 2025
What to do if my Graco Husky 2200 operates erratically?
- L
  laurawhitneyAug 28, 2025
  If your Graco Water Pump is operating erratically, several issues could be the cause. Start by inspecting the suction line for clogs and clear them. Check the check valve balls for stickiness or leaks, and clean or replace them if necessary. A ruptured diaphragm could also be the problem, so replace it. Ensure there is no restricted exhaust by removing any restrictions. Damaged or worn pilot valves or air valve can cause this issue, so replace them if needed. Also, check the air valve gasket for damage and replace it if necessary. An erratic air supply can cause this issue, so repair the air supply. Finally, exhaust muffler icing can lead to erratic operation, so use a drier air supply.
K
Karl DavisAug 29, 2025
What to do if my Graco Husky 2200 Water Pump leaks fluid externally from joints?
- M
  Mary RiveraAug 29, 2025
  If your Graco Water Pump is leaking fluid externally from joints, it's likely due to loose manifold screws or fluid cover screws; tighten them. Another possibility is worn-out manifold o-rings, which should be replaced.
L
Leah WilliamsAug 30, 2025
How to fix a Graco Water Pump that won't cycle?
- C
  christophercummingsAug 30, 2025
  If your Graco Water Pump won't cycle, or cycles once and stops, the air valve might be stuck or dirty; disassemble and clean it, ensuring you use filtered air. Another potential cause is a severely worn check valve ball wedged in the seat or manifold, in which case you should replace the ball and seat. A worn, damaged, or plugged pilot valve could also be the issue, so replace the pilot valve. Check for a damaged air valve gasket and replace it if necessary. Finally, a clogged dispensing valve could be the cause; relieve the pressure and clear the valve.
J
Jessica VegaSep 1, 2025
Why does my Graco Water Pump exhaust air contain fluid?
- L
  Linda DiazSep 1, 2025
  If the exhaust air of your Graco Water Pump contains fluid, the diaphragm is likely ruptured and needs to be replaced. Another possible cause is a loose diaphragm shaft bolt, which should be tightened or replaced.
M
Mrs. Julie WestSep 3, 2025
Why does my Graco Water Pump exhaust excessive air at stall?
- J
  John Branch MDSep 3, 2025
  If your Graco Water Pump exhausts excessive air at stall, the air valve cup or plate may be worn and needs replacement. Other potential causes include a damaged air valve gasket or damaged pilot valve, both of which should be replaced. Also, worn shaft seals or bearings can cause this issue, so replace them if necessary.
M
Mr. Peter GoodwinSep 4, 2025
Why does my Graco Husky 2200 Water Pump cycle at stall but fails to hold pressure?
- T
  Travis HermanSep 4, 2025
  If your Graco Water Pump cycles at stall but fails to hold pressure, it's likely due to worn check valve balls, seats, or o-rings, which will need to be replaced.

Graco Husky 2200 Specifications

General

Maximum Fluid Pressure	120 psi (8.4 bar)
Maximum Suction Lift	30 ft (9.1 m) wet
Maximum Solid Size	1/4 in (6.3 mm)
Wetted Parts	Polypropylene, Stainless Steel
Max Flow Rate	2200 L/min (581 GPM)
Power Source	Air Operated
Type	Air-operated double diaphragm pump
Fluid Inlet Size	2 in npt(f)
Fluid Outlet Size	2 in npt(f)