Graco Reactor 3 E-20 Elite - Setup Screens

AdvanceDisplayModule(ADM)
Setup Setup
Setup
Screens Screens
Screens
UsetheSetupscreensscreenstoeditsettings
fortheReactorsystem.
Pressure/Flow Pressure/Flow
Pressure/Flow
UsethePressure/Flowscreentosetpressure
monitoringsettingsfortheReactorsystem.
Setting Setting
Setting
Description Description
Description
EnableAuto
PressureBalance
Thisfeaturemonitorsthepressure
imbalancewhilematerialisowing
andaddstemperatureoffsetstothe
setpointstominimizethepressure
imbalance.
Tapthecheckboxtoenable/disable
AutoPressureBalance.Tap
thenumbervaluetoadjustthe
temperatureoffsetlimitallowed
usingAutoPressureBalance.
NOTE: NOTE:
NOTE:
Thisfeatureisonlyenabled
onProandElitemodels.
EnablePressure
ImbalanceAlarms
Tapthecheckboxtoenable/disable
PressureImbalanceAlarms.Tapthe
numbervaluetoadjustthealarm
threshold.
NOTE: NOTE:
NOTE:
Pressureimbalancealarmsare
automaticallyenablesifowmeters
areenabled.
EnablePressure
Imbalance
Deviations
Tapthecheckboxtoenable/disable
PressureImbalanceDeviations.Tap
thenumbervaluetoadjustthe
deviationthreshold.
EnableReactor
SmartControl
Tapthecheckboxtoenable/disable
ReactorSmartControl.Thisfeature
doesthefollowing:
•Slowsdowntheproportionerpump
ifinletpressureislow.Thisis
donetoallowthetransferpumps
tokeepupandavoidoff-ratio
conditions.
•Controlstheoutputpressuretothe
averageoftheAandBpressure
sensors(insteadofthemax).
EnableFlow
Meters
Tapthecheckboxtoenable/disable
owmeters.
EnableFlowMeter
Alarms
Tapthecheckboxtoenable/disable
owmeteralarms.Tapthenumber
valuetoadjustthealarmthreshold.
NOTE: NOTE:
NOTE:
Flowmeteralarmsareonly
availablewhenowmetersare
installed.
FlowMeterA
K-Factor
Tapthenumbervaluetoenterthe
K-FactorfortheAsideowmeter.
NOTE: NOTE:
NOTE:
TheK-Factorisnotedonthe
meterlabel.
FlowMeterB
K-Factor
Tapthenumbervaluetoenterthe
K-FactorfortheBsideowmeter.
NOTE: NOTE:
NOTE:
TheK-Factorisnotedonthe
meterlabel.
Heat Heat
Heat
UsetheHeatscreentocalibratehoseheatand
setthehosecontrolmode.
Tocalibratethesystem,seethe
Calibration,page36.
Setting Setting
Setting
Description Description
Description
HoseControl
Mode
Taptoselecthosecontrolmode.
FTS: FTS:
FTS:
controltotargettemperature
usinganFTS(uidtemperature
sensor)oneachsideofthe
hose.Calibrationisrequired
touseFTScontrolmode.See
CalibrationProcedure,page36.
Resistance: Resistance:
Resistance:
controltotarget
temperatureusingtheresistanceof
theheaterelement(changeswith
temperature).Calibrationisrequired
touseResistancecontrolmode.See
CalibrationProcedure,page36.
Manual: Manual:
Manual:
controltotarget
current(amps)toheatthehose.
Manualcontrolmodehasno
pre-programmedcontrolandis
designedtobeusedforalimited
amountoftimeuntilaproper
calibrationcanbeperformedorFTS
issuescanberesolved.
NOTE: NOTE:
NOTE:
Whenmanualhosemodeis
enabled,themanualhosemode
advisory(EVCH)willappear.
HoseACalibration
Factor
Resistancevaluedeterminedduring
thecalibrationprocessfortheAside
hose.
HoseBCalibration
Factor
Resistancevaluedeterminedduring
thecalibrationprocessfortheBside
hose.
LastCalibration
Date
Date/timeoflastsuccessful
calibration.
44
3A8500A