GRAPHTEC FC9000-160

To Next Page

To Previous Page

18-5

Rear view

This section explains in the FC9000-140.

0HGLDÁDQJHIRUWDNHXS

0HGLDÁDQJHIRUWDNHXS ........Supports media feeding.

Main Page

Default Chapter3
- Preface3
- About the Words and Phrases in this Text4
- Special Precautions on Handling Blades5
- After Turning on the Plotter6
- Machine Caution Label6
- Notes on the Stand6
- Notes on the Basket6
- Notes on the Paper (Media)7
- Precautions When Using the Curled Media7
- Installation Space9
- Selecting a Power Cable10
  - Table of Contents11
Chapter 1: Product Summary19
- Checking the Accessories20
  - Accessories20
  - Dedicated Accessories21
- Nomenclature22
  - Front View22
  - Rear View23
- Assembling24
  - Mounting the Stock Shafts24
- Connecting to the Computer25
Chapter 2: Preparing to Cut27
- Preparation of Cutter Plunger28
- Attaching a Tool31
  - Removing the Tool32
- Loading Media (Paper or Marking Film)33
  - Loading Roll Media33
  - Loading Sheet Media39
- Aligning the Push Rollers42
  - Aligning the Push Roller42
  - Changing the Hold-Down Force44
    - Switching44
    - Assignment45
- About the Default Screen46
- Connecting to the Power47
- How to Use Control Panel48
- Setting Feeding Method53
- Pre Feed of Media (Paper or Marking Film)55
- Selecting Tool Condition56
- Running Cutting Tests69
  - Cutting Test69
    - To Make 1 Cut with Set Value69
    - To Make 3 Cuts with Set Value and ±1 of Set Value70
- Displaying Cutting Area75
Chapter 3: Basic Operations77
- Raise or Lower the Tool78
- Move the Tool Carriage and Media79
- Setting the Origin Point83
- Setting the Cutting Direction86
- Stop Cutting88
  - Pause and Resume Cutting88
Chapter 4: Convenient Functions91
- Settings for Cutting92
- Copy (Duplicate Cutting)100
- Panel Cutting109
- Cross Cut Force111
  - User Switching113
Chapter 5: ARMS (Advanced Registration Mark Sensing System)115
- Outline of ARMS116
Chapter 6 : Manual Position Adjust151
Chapter 7: Setting Regarding Cutting Quality151
- Cutting the Corner of Thick Media Sharp152
- Setting the Step Pass158
- Setting the Offset Angle160
- Setting Cut Line Pattern165
- Setting the OFFSET FORCE171
  - In the Case of Tool 1 - Tool 3172
  - Between Tools 1 and 2175
- Cross Cut the Roll Paper179
Chapter 8: Settings Regarding Cutting Time183
- Sorting the Cutting Data184
- Perform Automatic Pre Feed When Cut Data Is Received186
- Perform Automatic Pre Feed When Media Is Set (Initial Feed)188
- Setting Feed Speed for Pre Feed189
- Setting the MOVING SPEED191
- Setting the Tool up Move193
- Setting the Tool up Height195
Chapter 9: Setting Regarding Interface197
- Setting Interface198
- Clearing the Buffer Memory200
- I/F (Lan)201
  - Setting the DHCP201
  - Set IP Address, Subnet Mask, Gateway203
- Connecting with RS-232C206
  - Switching the Setting Number You Want to Use206
  - Changing/Storing the RS-232C Setting207
Chapter 10: Settings Regarding Operation Environment211
- Related to Menu Display212
  - Display Language Setting (LANGUAGE SELECTION)212
  - Display Length Unit Setting (LENGTH UNIT)213
- Related to Sensor214
  - Enabling/Disabling the Media Sensors (MEDIA SENSOR)214
  - Enabling/Disabling the Push Roller Sensors (PUSH ROLLER SENSOR)215
- Related to Plotter Environment217
Chapter 11: Settings of Controls from Computer223
- Related to Command Processing224
  - Setting the Command (COMMAND)224
  - Priority of Tool Condition Selection (CONDITION PRIORITY)225
- Related to GP-GL Command226
  - Enabling/Disabling the ' : ' and ' ; ' Commands (COMMAND ' : ', ' ; ')227
  - Moving the Pen While Raised or Lowered in Response to the 'W' Command (COMMAND 'W')228
- Related to HP-GL Command229
  - Model ID Response (HP-GL MODEL EMULATED)229
  - Circle-Command Resolution Setting (CIRCLE RESOLUTION)230
Chapter 12: Data Link231
- Select Connection Destination232
- Data Link with USB Memory233
- Output with a Barcode235
- Start Mark Auto Scan238
- Communication Timeout240
- Skew Scanning242
Chapter 13: Apparel (AP) Mode245
- Apparel (AP) Mode246
- Set F Command of Cutting (F_CUT)253
- Cutting a CUT DEMO254
- Setting a Time out256
- Setting a Separator258
  - GP-GL Separator258
  - HP-GL Separator259
- Running Cutting Tests263
  - Cutting Test263
- Cross Cut Settings266
- Setting Rear Margin268
- Setting the Number of Pre Feeds270
- Setting Paper Exposure Time272
Chapter 14: Cutting with Supplied Application Software275
- Basic Operation of Printing and Cutting276
  - Graphtec Pro Studio / Cutting Master 4276
  - Graphtec Studio285
- Basic Operation of Barcode289
  - Graphtec Pro Studio / Cutting Master 4289
- Application of Barcode Cutting (Continuous Operation)297
  - Graphtec Pro Studio297
Chapter 15: Maintenance311
- Daily Maintenance312
  - Storing the Plotter312
- Replacing Cutter Blade313
- Cleaning the Cutter Pen315
- Cutter Plunger Exchange316
- Setting the Alarm for Degree of Wear (BLADE WEAR ALARM)317
- Replacing the Cross Cut Unit321
Chapter 16: Troubleshooting323
- Troubleshooting324
- Printing the Setting of the Plotter338
- Creating Test Pattern340
- Creating CUTTING PRO342
- Self Diagnostic Test346
  - Reading the Error Message348
Chapter 17: Option351
- Pouncing (Punch Continuous Holes)352
- 2-Pen Assignment (Switching the Tools)355
Chapter 18: Take-Up359
- Precautions (Take-Up)360
- Nomenclature (Take-Up)362
  - Front View362
  - Rear View363
- Preparation for Plotting/Cutting (Take-Up)364
- Troubleshooting (Take-Up)377
Appendix (Take-Up)379
- External Dimensions384

GRAPHTEC FC9000-160 - Rear View

Table of Contents

Other manuals for GRAPHTEC FC9000-160

Related product manuals