Why does my GRAPHTEC FC8600 tool move up and down so much?
If your Graphtec Plotter has too many tool up and down movements, the setting for the tangential mode is set to ON. Turn OFF the setting for the tangential mode unless you are cutting thick media.
How to fix tilted media on GRAPHTEC FC8600 Plotter?
If the Graphtec Plotter media travels tilted, it could be that the media is loaded tilted. Reload the media.
How to resolve scan errors with registration marks on GRAPHTEC FC8600 Plotter?
If registration marks cannot be scanned properly on your Graphtec Plotter because of scan errors, and there are smears within the scanning area, remove the smears.
Why does my GRAPHTEC Plotter display 'POSITION ALARM' during cutting?
If the CONDITION setting for the media is invalid, slow down the speed or lower the FORCE.
Why are corners rounded/sharp on my GRAPHTEC FC8600 Plotter cuts?
If the Graphtec Plotter corners are rounded or too sharp, the blade and OFFSET do not match. Change the OFFSET. Increase the OFFSET if it is rounded, and decrease the OFFSET if it is too sharp.
How to fix a GRAPHTEC FC8600 Plotter when no lights are on?
Check that the power cord is securely connected to the plotter's AC line inlet and the electrical outlet. Check that the power is supplied to the electrical outlet. Contact your Graphtec call center if the problem still exists.
Why is my GRAPHTEC FC8600 blade skipping?
If the Graphtec Plotter blade skips and does not completely cut lines that should be solid, and straight cut lines seem to wobble, and the cutting speed is too high, lower the speed setting.
Why does my GRAPHTEC FC8600 say 'LOAD MEDIA!' when media is loaded?
If your Graphtec Plotter displays "LOAD MEDIA!" even if the media is set and the media set lever is moved up, it may be because the media is close to transparent, causing the media sensor to make a false recognition. Transparent media cannot be detected. Disable the media sensor and set the cut area when using this kind of media.
What to do if my GRAPHTEC Plotter lights up but doesn't operate?
Contact your Graphtec call center if the problem still exists.
What causes 'POSITION ALARM' on my GRAPHTEC FC8600?
If the Graphtec Plotter stops with "POSITION ALARM" during initialization or cutting, it may be caused by movement being disturbed by media chaff in the operation area. Remove the object disturbing the operation, and turn the plotter on again after turning it off.
Lists safety warnings to prevent fatal or serious injury if ignored.
Provides steps for assembling the plotter stand and related parts.
Explains how to connect the plotter to a computer via interface cables.
Describes the nomenclature and structure of cutter pens.
Details the procedure for attaching a tool (cutter pen or plotter pen) to the plotter.
Guides on loading roll media and sheet media into the plotter.
Describes the steps for powering on the plotter.
Explains the functions of lamps and keys on the control panel.
Allows setting tool, speed, force, and acceleration for 8 different conditions.
Guides on performing test cuts to optimize cutting conditions.
Introduces ARMS function for scanning registration marks and its purpose.
Covers setting MARK SCAN mode, numbers, shape, size, and distance.
Explains methods to adjust position using ARMS with 2, 3, or 4 points.
Details the method for manually adjusting position, including axis tilt and distance.
Describes how to set USB, Network (LAN), and RS-232C interfaces.
Provides precautions for daily plotter operation and cleaning.
Guides on how to replace the cutter blade.
Details the procedure for replacing the cross cut unit.
Provides troubleshooting for common issues like media wobbling or tool carriage errors.
Offers solutions for errors related to registration mark scanning.
Addresses issues with cut quality, such as rounded corners or dull blades.
Lists and explains error messages related to the ARMS system.
Guides on performing a self-diagnostic test of sensors and switches.
Lists key technical specifications of the FC8600 Series plotters.
General| Power Supply | AC 100-240V, 50/60Hz |
|---|---|
| Maximum Cutting Speed | 1485 mm/s |
| Mechanical Resolution | 0.005 mm |
| Repeatability | ±0.1 mm |
| Interface | USB, Ethernet, Serial (RS-232C) |
| Media Types | Reflective film |
| Programmable Resolution | 0.025 mm (0.001 in) |
| Command Sets | HP-GL, GP-GL |
| Blade Type | Supersteel blade |
| Optional Accessories | Stand, Basket |
To Next Page
