What to do if SOFT LED is off and pump motor doesn't operate on Hach Measuring Instruments?
If the SOFT LED light isn't on and the pump motor isn't running on your Hach Measuring Instruments, check the following: * Ensure the power switch is on. * Connect the power cord securely. * If needed, replace the fuses.
How to set the flow rate for accurate readings on Hach 5410001 Measuring Instruments?
To ensure the sample cell in your Hach Measuring Instruments flushes completely, set the flow rate to 200 mL/minute. This prevents a zero reading caused by insufficient flushing or dilution from bypassing the pinch block.
How to fix the 'No stir bar is installed' error on my Hach Monitor?
• Ensure that a stir bar is installed in the Hach Monitor. • If necessary, use a paper clip to retrieve the stir bar from the colorimeter, and verify that only one stir bar is installed. • If the stir bar does not operate, manually mix the sample after adding reagents for approximately 10 seconds using a wooden Q-tip. If the instrument then gets a reading, the mixing was insufficient, and you should replace the stir coil.
What to do if the Hach Monitor does not receive any buffer or indicator solution?
If the Hach Monitor isn't receiving buffer or indicator solution, remove the two reagent lines from the Y connector. Only one drop of reagent should come out per cycle. If no reagent comes out, inspect the pressure plate. Ensure the pinch block isn't overtightened and the reagent lines aren't pinched. Check the back of the pinch block for grooves and replace the pinch block if needed.
What to do if the Hach Monitor does not operate correctly?
To troubleshoot a Hach Monitor that isn't operating correctly, pinch the sample inlet line to stop the sample flow. The next cycle should read soft. If it doesn't, check the LED for an orange light. Also, examine the photocell and clean it if needed. After this cycle, the instrument should read hard again.
What to do if the Hach Monitor chemistry does not operate correctly?
If the chemistry in your Hach Monitor isn't working correctly, mix 1 mL of each reagent with 80 mL of the sample. You should observe a color change. If there is no color change, the reagents need to be replaced.
Why does my Hach Monitor show hard water with a continuous red LED?
If the flow rate is not correct, the Hach Monitor may show hard water and a continuous red LED. A flow rate that's too low can prevent the sample cell from completely flushing out the color, leading to a zero reading. A flow rate that's too high can cause water to bypass the pinch block, diluting the color. Ensure the flow rate is set to 200 mL/minute. Additionally, check the sample line in the pinch block to ensure it's not pinched off. Adjust the flow rate to 200 mL/minute while observing a steady water stream. Also, make sure the pressure plate of the pinch block is not overtightened and inspect the back of the pinch blocks for grooves.
What to do if display doesn't light but the pump motor operates on Hach Monitor?
If the display doesn't light, but the pump motor operates on the Hach Monitor, the problem may be with the power supply. Replace the circuit board.
How to troubleshoot a Hach Monitor when the display doesn't light and the pump motor isn't operating?
If the display does not light and the pump motor is not operating on your Hach Monitor, check the power switch position, fuse, and power cord connections to ensure they are properly connected.
What to do if display lights and the pump motor does not operate on Hach Monitor?
If the display lights up but the pump motor doesn't operate on your Hach Monitor, here are a few things to check: 1. Low operating power: Verify the line voltage is within specifications. 2. Incorrect line voltage selector switch setting: Check the line voltage selector switch position. 3. Motor cable not connected: Check the motor cable connection to the circuit board. 4. Defective motor: Replace the motor.
General| Brand | Hach |
|---|---|
| Model | 5410001 |
| Category | Measuring Instruments |
| Language | English |
To Next Page