To Next PageTo Next Page
Need help?Do you have a question about the Helmholz NETLink 700-881-MPI21 and is the answer not in the manual?
General| Model | NETLink 700-881-MPI21 |
|---|---|
| Category | Gateway |
| Manufacturer | Helmholz |
| Interface | MPI, PROFIBUS, Ethernet |
| Power Supply | 24 V DC |
| Storage Temperature | -20°C to +70°C |
| Certification | CE, UL |
| Protocol | TCP/IP |
| Operating Temperature | 0°C to 60°C |
| Humidity | 95% non-condensing |
General safety information regarding the use of NETLink® Gateway.
Modules require restricted access to installation locations.
Manual provides operational and technical data for users and technicians.
Specifies that NETLink® Gateways are for communication and signaling.
Warning against using NETLink® for safety-related functions or uncontrolled restarts.
NETLink® Gateways can be installed in any orientation.
Details minimum clearances required around NETLink® modules.
Details on installing various NETLink® module types.
Mounting options for POE and WLAN versions using brackets.
Installation of the Compact version directly into PROFIBUS stations.
NETLink® acts as a gateway between TCP and fieldbus networks.
Details features of PoE and WLAN versions, including power and wireless connectivity.
Describes the Compact version's PROFIBUS interface and isolation.
Describes the various physical connections available on NETLink® devices.
Explains the meaning of the LEDs on NETLink® Gateways for status indication.
Details the function of the LINK and ACTIVE LEDs on the RJ45 connector.
Explains the three LEDs on the top of the NETLink® for device status.
Details the LED indicators on the NETLink® PRO Compact.
Lists the items delivered with each NETLink® device.
Lists available accessories for NETLink® devices.
Information on how to obtain NETLink® manuals.
Information on diagnostic and update software for NETLink® devices.
Lists specific accessories like DIN rail brackets and power adapters.
Lists available WLAN antennas and antenna cables.
Introduces the NETLink-S7-NET driver for accessing controllers via TCP/IP.
Outlines PC requirements and tested software for driver installation.
Steps for downloading and running the NETLink-S7-NET driver setup.
Guide to setting up the NETLink-S7-NET interface in the PG/PC settings.
How to select the correct NETLink® PRO Family interface in PG/PC settings.
Configuration of NETLink® for MPI, PPI, and PROFIBUS bus systems.
Configuration of MPI bus parameters including address and transmission rate.
Configuration of PROFIBUS bus parameters, profiles, and rates.
Configuration of PPI bus parameters, including address and transmission rate.
Methods for parameterizing NETLink® devices via TCP.
Steps to set up a NETLink® station for driver access.
How to change TCP parameters like IP address and port.
Configuring static IP addresses for NETLink® without a DHCP server.
Configuring NETLink® to obtain IP parameters automatically via DHCP.
Options for naming, web interface activation, and password changes.
Settings for driver language and reading version information.
How to set the display language for the driver interface.
Displays version numbers of driver files for support.
Tools for diagnosing connected bus nodes and parameters.
Displays a list of all active and passive nodes on the bus.
Displays available bus parameters for diagnostics.
Describes the initial web interface page and navigation.
Steps to set up user access and password for the web interface.
Provides device information like firmware version and connections.
Interface for modifying device parameters, TCP, and bus settings.
Interface for setting up access restrictions, including IP whitelisting.
Function to monitor variables via the web interface, similar to Simatic tools.
Section dedicated to configuring NETLink® WLAN adapter functions.
Configuration for WLAN in infrastructure mode with an access point.
Configuration for WLAN in ad hoc mode for peer-to-peer communication.
Steps to connect a PC to NETLink® WLAN in unencrypted ad hoc mode.
Steps to connect a PC to NETLink® WLAN in encoded ad hoc mode.
How to address specific modules using Rack/Slot and TSAP for RFC1006.
How to store specific bus parameters for MPI, PPI, and PROFIBUS.
Enables communication with multiple CPUs on a rack using TSAP.
Enables addressing multiple CPs via their PROFIBUS addresses using TSAP.
Provides general technical specifications for NETLink® devices.
Specific technical data for the NETLink® PRO PoE model.
Specific technical data for the NETLink® WLAN model.
Specific technical data for the NETLink® PRO Compact model.
Details the pin assignments for MPI/PROFIBUS and Ethernet interfaces.
Pinout for the MPI/PROFIBUS connector.
Pinout for the Ethernet interface connector.
Lists additional resources and links for more information.
Links to relevant websites for further information.
Lists publications and technical rules for communication systems.
Table for parameterizing RFC routing and remote TSAP addresses.
