Henkovac M2 - User Manual

Questions and Answers

C
Claire HawkinsAug 5, 2025
What to do if my Henkovac Kitchen Appliances machine does not work?
- D
  donald31Aug 5, 2025
  If your Henkovac Kitchen Appliance machine isn't working, there are several potential causes: * The machine might not be plugged into the electrical outlet. In this case, plug the machine into the electrical outlet. * The ground fault safety in the electrical panel may have tripped. Check the electrical panel. * A fuse in the electrical panel might be faulty. Check the electrical panel. * A fuse in the machine could be faulty. Consult your dealer. * The motor protection of the machine might be switched off. Consult your dealer.
H
harrisjasonAug 9, 2025
Why is the seal leaking on my Henkovac M2?
- J
  jaime61Aug 10, 2025
  If the seal is leaking on your Henkovac Kitchen Appliances, it could be due to several reasons: * The package seam may be poorly formed. Try increasing the sealing time and/or reducing the MAP gas pressure. * The package seam might be burnt. Decrease the sealing time. * The opening of the vacuum bag could be contaminated. Try again, ensuring the bag opening stays clean. * The sealing beam might be dirty. Clean the sealing beam. * The Teflon lining of the sealing beam could be damaged. Replace the Teflon lining. * The silicon rubber seal in the counter beam might be damaged. Replace the silicon rubber seal.
T
Tanya SullivanAug 14, 2025
How to fix a Henkovac Kitchen Appliances machine that does not seal?
- J
  John PalmerAug 14, 2025
  If your Henkovac Kitchen Appliances machine isn't sealing, consider these possibilities: * The bag isn't correctly positioned over the sealing beam. Adjust the bag position. * The sealing wire is broken. Replace the sealing wire. * The thermal safety of the power supply was tripped. Wait until the safety resets, which can take half an hour. Decrease the sealing time. * The electrical contacts of the seal beam have fouled. Remove the seal beam and clean the pins and contacts with sand paper.
P
peggy19Aug 18, 2025
What to do if the vacuum in the package is insufficient in Henkovac M2 Kitchen Appliances?
- M
  Michael NealAug 18, 2025
  If the vacuum in the package is insufficient with your Henkovac Kitchen Appliances, it might be because: * The programmed vacuum value is too high. Lower the vacuum value in the program. * The packaging material is of poor quality. Select a better-quality packaging material. * The product damages the bag. Program a higher value for Soft-Air. * The machine gases the package. Turn off the gassing function.
J
Jeremy DavisAug 22, 2025
Why doesn't the vacuum pump run at full speed on my Henkovac M2 Kitchen Appliances?
- R
  Richard RodriguezAug 22, 2025
  If the vacuum pump on your Henkovac Kitchen Appliances isn't running at full speed: * The oil might be too thick or contaminated. Consult your dealer. * The pump motor may be running on two phases. Consult your dealer.
T
Tracy WilsonAug 27, 2025
What causes not enough gas in the bag with Henkovac M2?
- S
  stephendeleonAug 27, 2025
  If there is not enough gas in the bag when using your Henkovac Kitchen Appliances, it could be due to: * The bag being too small. Select a bigger bag. * The programmed gas level being too low. Increase the gas level value. * The bag not being correctly positioned over the gas outlets. Adjust the bag position.
M
millerlisaAug 31, 2025
How to reset the service symbol on Henkovac M2 Kitchen Appliances?
- J
  Justin BriggsAug 31, 2025
  To reset the service interval counters on your Henkovac Kitchen Appliances after an oil change: start the machine, and while the display shows the hours or cycles, press and hold the button.