EasyManua.ls Logo

Henkovac D3 - User Manual

Default Icon
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
art.nr. 9606.041EN
User Manual
Vacuum Packaging Machines
T2, T3, T4, T5, T6 M1, M2, M3 M4, M5, M6 M7, M8 D1, D3, D4 D6
http: //www.henkovac.com
e-mail: info@henkovac.com
tel: +31736271201
SERIAL NUMBER
1ST CHOICE FOR PROFESSIONALS WORLDWIDE

Table of Contents

Questions and Answers

  • K
    Kristine BarnesAug 5, 2025
    What to do if my Henkovac D3 Kitchen Appliances machine does not work?
    • J
      Jesse WongAug 5, 2025
      If your Henkovac Kitchen Appliance machine isn't working, there are several potential causes: * The machine might not be plugged into the electrical outlet. In this case, plug the machine into the electrical outlet. * The ground fault safety in the electrical panel may have tripped. Check the electrical panel. * A fuse in the electrical panel might be faulty. Check the electrical panel. * A fuse in the machine could be faulty. Consult your dealer. * The motor protection of the machine might be switched off. Consult your dealer.
  • F
    frederickbrittanyAug 9, 2025
    Why is the seal leaking on my Henkovac Kitchen Appliances?
    • N
      Nicholas SmithAug 9, 2025
      If the seal is leaking on your Henkovac Kitchen Appliances, it could be due to several reasons: * The package seam may be poorly formed. Try increasing the sealing time and/or reducing the MAP gas pressure. * The package seam might be burnt. Decrease the sealing time. * The opening of the vacuum bag could be contaminated. Try again, ensuring the bag opening stays clean. * The sealing beam might be dirty. Clean the sealing beam. * The Teflon lining of the sealing beam could be damaged. Replace the Teflon lining. * The silicon rubber seal in the counter beam might be damaged. Replace the silicon rubber seal.
  • G
    Gail ColeAug 13, 2025
    How to fix a Henkovac D3 Kitchen Appliances machine that does not seal?
    • V
      vburtonAug 13, 2025
      If your Henkovac Kitchen Appliances machine isn't sealing, consider these possibilities: * The bag isn't correctly positioned over the sealing beam. Adjust the bag position. * The sealing wire is broken. Replace the sealing wire. * The thermal safety of the power supply was tripped. Wait until the safety resets, which can take half an hour. Decrease the sealing time. * The electrical contacts of the seal beam have fouled. Remove the seal beam and clean the pins and contacts with sand paper.
  • M
    Meagan SandovalAug 17, 2025
    What to do if the vacuum in the package is insufficient in Henkovac D3?
    • J
      Jeremiah RoachAug 17, 2025
      If the vacuum in the package is insufficient with your Henkovac Kitchen Appliances, it might be because: * The programmed vacuum value is too high. Lower the vacuum value in the program. * The packaging material is of poor quality. Select a better-quality packaging material. * The product damages the bag. Program a higher value for Soft-Air. * The machine gases the package. Turn off the gassing function.
  • J
    jgrahamAug 22, 2025
    Why doesn't the vacuum pump run at full speed on my Henkovac D3?
    • T
      truizAug 22, 2025
      If the vacuum pump on your Henkovac Kitchen Appliances isn't running at full speed: * The oil might be too thick or contaminated. Consult your dealer. * The pump motor may be running on two phases. Consult your dealer.
  • B
    Brandon MitchellAug 27, 2025
    What causes not enough gas in the bag with Henkovac D3?
    • T
      Tina TaylorAug 27, 2025
      If there is not enough gas in the bag when using your Henkovac Kitchen Appliances, it could be due to: * The bag being too small. Select a bigger bag. * The programmed gas level being too low. Increase the gas level value. * The bag not being correctly positioned over the gas outlets. Adjust the bag position.
  • M
    Melissa GilbertAug 31, 2025
    How to reset the service symbol on Henkovac D3?
    • J
      Jessica Jones DDSAug 31, 2025
      To reset the service interval counters on your Henkovac Kitchen Appliances after an oil change: start the machine, and while the display shows the hours or cycles, press and hold the button.

Summary

Safety Regulations and Warnings

General Safety Guidelines

Manufacturer liability, owner responsibility, user training, and label importance.

Intended Use and Modifications

Defines commercial use and prohibits machine modifications.

Specific Safety Measures

Lists standard safety devices like short-circuit protection and pump fan guards.

Welcome, Support, and Precautions

General Electrical Precautions

Instructions for grounding the machine and avoiding electric shock.

Machine Installation and Connections

General Installation Procedures

Guidelines for leveling, positioning, and checking machine oil level.

Electrical, Gas, and Air Connections

Procedures for connecting power, MAP gas, and compressed air.

Digital Control System

LCD Display and One-Program System

Describes the LCD display and machines with a single program (P1).

Operating the One-Program Control System

Adjusting Vacuum and Sealing Times

Ten-Program Control System Overview

Time-Based and Sensor-Based Operation

Operating the Ten-Program Control System

Machine On;Off and Cycle Control

Program Value Adjustment and Navigation

Programming the Machine

One-Program Control System Details

Programmable Functions for P1-P9

Packing Cycle Progress Symbols

Cycle Progress Indicators

Packaging Concepts Explained

Sensor-Based and Time-Based Control

Specialized Programs

Details liquid product, Vacuum Plus, and MAP Gassing features.

Sealing Methods and Extra Pressure

Extra Sealing Pressure

Advanced Packaging Features

Soft-Air Feature

Multi-Cycle and Oil Dehumidification

Machine Maintenance and Pump Care

General Maintenance Importance

Vacuum Pump Maintenance Procedures

Tasks for protecting and maintaining the vacuum pump, including cleaning and oil checks.

Pump Oil Management

Adding and Changing Pump Oil

Instructions for adding and changing pump oil, including recommended types.

Seal Beam and Counter Beam Maintenance

Single-Seal Beam Maintenance

Troubleshooting and Technical Support

Malfunctions and Troubleshooting Guide

Guides for resolving common malfunctions and their causes.

Service and Technical Support Contact

Contact information for resolving technical problems and seeking support.

Recommended Spare Parts

Spare Parts Catalog

Henkovac D3 Specifications

General IconGeneral
BrandHenkovac
ModelD3
CategoryKitchen Appliances
LanguageEnglish

Related product manuals