What to do if Henny Penny KFC Velocity shows E-41P-1- LOST error?
If your Henny Penny Fryer displays the error code E-41P-1- LOST, it means that system data lost, both the RAM copy and stored copy of the settings have been lost and settings are reset to default. Further assistance is needed.
How to fix Henny Penny KFC Velocity if oil is not draining?
If the oil is not draining from your Henny Penny Fryer, it may be because the drain valve is clogged. Push a cleaning rod through the open drain valve to resolve this.
What to do if Henny Penny Fryer filter motor won’t run?
If the filter motor on your Henny Penny Fryer won’t run, it could be that the motor has overheated. Reset the motor.
Why is my Henny Penny KFC Velocity power switch on but the fryer is completely inoperative?
If your Henny Penny Fryer's power switch is on but the unit isn't working, it suggests an open circuit. Ensure the fryer is plugged in, check the breaker or fuse at the wall, and inspect the circuit breakers between the control panel and ATO tank.
Why is my Henny Penny Fryer oil not heating?
If the oil in your Henny Penny Fryer is not heating, it might be because the high temperature limit has tripped. Reset the high temperature limit.
What to do if Henny Penny KFC Velocity Fryer shows E-15C DRAIN VALVE ERROR?
If your Henny Penny Fryer displays the error code E-15C DRAIN VALVE ERROR, it means that the drain valve doesn’t fully closed. Unclog the drain with a drain brush. If the error persists, further assistance is needed.
What to do if Henny Penny KFC Velocity Fryer shows E-10 (A thru Y) error?
If your Henny Penny Fryer displays the error code E-10 (A thru Y), it indicates that the high limit has tripped. Reset the high limit trip. The reset momentary switch is below the control panel heat vents, under the lip, above the condensation tank (box). Perform a clean out. If the error persists, further assistance is needed.
What to do if Henny Penny Fryer shows E-6A MAIN TEMP PROBE FAILED (Open Circuit) error?
If your Henny Penny Fryer displays the error code E-6A MAIN TEMP PROBE FAILED (Open Circuit), it indicates a temperature probe failure. Turn the switch to off position, then turn the switch back to on. If the error persists, further assistance is needed.
Why does my Henny Penny Fryer pressure not build?
If pressure isn't building in your Henny Penny Fryer, several factors could be responsible. First, ensure there is enough product in the vat, especially when using fresh oil. Second, check the programming to confirm the pressure is correctly set. Finally, inspect the lid gasket for leaks and reverse or replace it if necessary.
What to do if my Henny Penny KFC Velocity displays E-1 LOW OIL IN POT?
If your Henny Penny Fryer shows the E-1 error with the message LOW OIL IN POT!, it means the oil level is too low. This happens because the top heating element, where the probe is located, gets hotter than it would if submerged in oil. Check the oil level to ensure it is above the main probe.
General| Brand | Henny Penny |
|---|---|
| Model | KFC Velocity Series |
| Category | Fryer |
| Language | English |
Ensure proper ventilation and meet all electrical specifications for safe installation.
Assemble drain pan, purge oil lines, and fill vat with oil following critical procedures.
Learn about oil breakdown factors, prevent boil-over, and understand filtering importance.
Follow steps for automated startup: heating, melt, mix, top-off, and polish.
Learn about manual, rear, and front bulk oil disposal processes.
Detailed steps for heated/cold-soak clean-out, including draining and rinsing.
Understand and correct system error codes displayed on the control board.
To Next Page
