What to do if pressure not exhausting at end of Cook Cycle in Henny Penny KFC Velocity Fryer?
If the pressure isn't exhausting at the end of the cook cycle in your Henny Penny Fryer, the solenoid or exhaust line might be clogged. Turn off the heat and allow the fryer to cool, which will release the pressure in the vat. Clean all lines, solenoids, and the exhaust tank.
Why is my Henny Penny KFC Velocity foaming or boiling over?
Foaming or boiling over in your Henny Penny Fryer can occur if oil stabilizers are not used. If you are frying product with excessive ice crystals, dip the product quickly once, remove it to allow the ice crystals to melt and excessive water to evaporate, then place it back into the fryer to cook normally.
Why is my Henny Penny KFC Velocity Fryer oil not draining?
If the oil is not draining from your Henny Penny Fryer, it's likely that the drain valve is clogged. To resolve this, push a cleaning rod through the open drain valve.
Why is my Henny Penny Fryer relief valve venting?
The relief valve on your Henny Penny Fryer might be venting because the operating pressure is too high or the deadweight is clogged. Turn off the heat and allow the fryer to cool, which will release the pressure in the vat. Clean the deadweight.
What to do if my Henny Penny KFC Velocity displays E-1 LOW OIL IN POT?
If your Henny Penny Fryer shows the E-1 error with the message LOW OIL IN POT!, it means the oil level is too low. This happens because the top heating element, where the probe is located, gets hotter than it would if submerged in oil. Check the oil level to ensure it is above the main probe.
What to do if my Henny Penny Fryer displays E-6A MAIN TEMP PROBE FAILED?
If your Henny Penny Fryer displays the E-6A error, it means the temperature probe has failed. Turn the fryer off, then back on. If the error continues, the temperature probe should be checked. Once the temperature probe is repaired or replaced, the controls should return to normal operation.
How to fix Henny Penny KFC Velocity when the power switch is on but the fryer is completely inoperative?
If your Henny Penny Fryer isn't working even with the power switch on, it indicates an open circuit. Ensure the fryer is plugged in and check the breaker or fuse at the wall. Also, check the circuit breakers between the control panel and the Automatic Top-off (ATO) tank.
What to do if my Henny Penny Fryer displays E-4 CPU TOO HOT?
If the Henny Penny Fryer displays E-4, it indicates the control board is overheating. Turn the fryer off, then back on. If the error continues, check for signs of overheating behind the control panel. Once the panel cools down, the controls should return to normal operation. If the E-4 error persists, replace the control.
What to do if my Henny Penny KFC Velocity displays E-5 OIL TOO HOT?
If your Henny Penny Fryer displays the E-5 error, it means the oil is overheating. First, turn the fryer off and then back on. If the error persists, the heating circuits and temperature probe should be checked. The controls should return to normal operation once the unit cools down. If the E-5 error continues, the control should be replaced.
Why is my Henny Penny Fryer oil not heating?
If the oil in your Henny Penny Fryer is not heating, it might be because the high temperature limit has tripped. Reset the high temperature limit.
General| Brand | Henny Penny |
|---|---|
| Model | KFC Velocity Series |
| Category | Fryer |
| Language | English |
Ensure proper ventilation and meet all electrical specifications for safe installation.
Assemble drain pan, purge oil lines, and fill vat with oil following critical procedures.
Learn about oil breakdown factors, prevent boil-over, and understand filtering importance.
Follow steps for automated startup: heating, melt, mix, top-off, and polish.
Learn about manual, rear, and front bulk oil disposal processes.
Detailed steps for heated/cold-soak clean-out, including draining and rinsing.
Understand and correct system error codes displayed on the control board.
To Next Page
