What to do if my Henny Penny Fryer shows 'E05'?
If the Henny Penny Fryer displays 'E05', it indicates the shortening is overheating. First, turn the switch OFF, then back ON. If the error persists, have the heating circuits and temperature probe checked. After the unit cools down, the controls should return to normal. If 'E05' continues, the controls may need replacement.
How to fix Henny Penny PFE-590 shortening not draining?
If the shortening is not draining, it may be because the drain valve is clogged. Try pushing a cleaning rod through the open drain valve to clear any blockages.
Why is my Henny Penny Fryer shortening not heating?
If your Henny Penny Fryer is not heating, first check if the drain valve is open and close it. If that's not the issue, the high-temperature limit may have tripped. In this case, reset the high-temperature limit; see Operating Components Section.
Why pressure does not build in Henny Penny PFE-590 Fryer?
If the pressure isn't building in your Henny Penny Fryer, several factors could be at play. Ensure you're using a full capacity of product in the frypot when using fresh shortening. Check that the metal shipping spacer has been removed from the deadweight assembly; see Unpacking Instructions Section. Verify the pressure is correctly programmed. Lastly, inspect the lid gasket for leaks and reverse or replace it if needed.
What to do if Henny Penny PFE-590 Fryer is foaming or boiling over?
If your Henny Penny Fryer is foaming or boiling over, follow the boil-over procedures from the chart.
What to do if filter motor won’t run in Henny Penny Fryer?
If the filter motor on your Henny Penny Fryer won’t run, it might be overheated. Try resetting the motor; see Filter Pump Motor Protector-Manual Reset Section.
What to do if pressure is not exhausting at end of cook cycle in Henny Penny Fryer?
If the pressure is not exhausting at the end of the cook cycle in your Henny Penny Fryer, the solenoid or exhaust line might be clogged. Turn the fryer OFF and allow it to cool to release the pressure in the frypot. Then, have all lines, the solenoid, and the exhaust tank cleaned.
Why is operating pressure too high in Henny Penny PFE-590 Fryer?
If the operating pressure of your Henny Penny Fryer is too high, the deadweight may be clogged. Turn the fryer OFF and allow it to cool down to release the pressure in the frypot. Clean the deadweight; see Cleaning the Deadweight Assembly Section.
What to do if Henny Penny PFE-590 Fryer pressure not exhausting at end of Cook Cycle?
If the pressure is not exhausting at the end of the cook cycle, it could be due to a clogged solenoid or exhaust line. Turn off the fryer and allow it to cool to release the pressure in the frypot. Have all lines, the solenoid, and the exhaust tank cleaned.
What to do if Henny Penny Fryer power switch is on but fryer completely inoperative?
If the fryer is completely inoperative, it might be due to an open circuit. Ensure the fryer is plugged in and check the breaker or fuse at the wall.
Essential safety information including hazard warnings and symbol explanations.
Procedures for ensuring the fryer is properly leveled for safe and efficient operation.
Specifications for electrical hookup, power supply, and safety grounding.
Detailed description of the fryer's various parts and their functions.
Instructions for safely opening and closing the fryer lid, including warnings.
Explanation of the control panel buttons, digital display, and indicators.
Step-by-step guide for the standard cooking process, including loading and unloading.
Common problems encountered during operation and their corresponding solutions.
Explanations of error messages displayed by the control system and corrective actions.
General| Model | PFE-590 |
|---|---|
| Category | Fryer |
| Type | Pressure Fryer |
| Power Source | Electric |
| Temperature Range | 200°F - 400°F |
| Oil Capacity | 50 lbs |
| Voltage | 208/240V |
| Phase | 3 |
To Next Page
