EasyManuals Logo

HIKVISION DS-7608NI-Q2/8P User Manual

HIKVISION DS-7608NI-Q2/8P
226 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #221 background imageLoading...
Page #221 background image
Network Video Recorder User Manual
220
Simultaneously press Ctrl and C to exit the ping command.
Step 2 Verify the frame rate is real-time frame rate.
Select “Menu > Record > Parameters > Record”, and set the Frame rate to Full Frame.
Step 3 Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from Hikvision to do the further process.
Live view stuck when video output remotely via the Internet Explorer or platform software.
Possible Reasons:
Poor network between NVR and IP camera, and there exists packet loss during the
transmission.
Poor network between NVR and PC, and there exists packet loss during the transmission.
The performances of hardware are not good enough, including CPU, memory, etc..
Step 4 Verify the network between NVR and IP camera is connected.
1) When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the
RS-232 cable.
2) Open the Super Terminal, and execute the command of “ping 192.168.0.0 l 1472 f (the
IP address may change according to the real condition), and check if there exists packet
loss.
Simultaneously press Ctrl and C to exit the ping command.
Step 5 Verify the network between NVR and PC is connected.
1) Open the cmd window in the Start menu, or you can press “windows+R” shortcut key
to open it.
2) Use the ping command to send large packet to the NVR, execute the command of “ping
192.168.0.0 l 1472 –f” (the IP address may change according to the real condition),
and check if there exists packet loss.
Simultaneously press Ctrl and C to exit the ping command.
Step 6 Verify the hardware of the PC is good enough.

Table of Contents

Other manuals for HIKVISION DS-7608NI-Q2/8P

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HIKVISION DS-7608NI-Q2/8P and is the answer not in the manual?

HIKVISION DS-7608NI-Q2/8P Specifications

General IconGeneral
DHCP clientYes
Input bandwidth80 Mbit/s
Maximum frame rate60 fps
Maximum resolution3840 x 2160 pixels
Alarm input channels1
Video input channels8 channels
Supported resolutions1024 x 768, 1280 × 720, 1280 × 1024, 1920 × 1080, 1600 × 1200, 3840 × 2160
Video recording modes720p, 1080p
Wi-FiNo
HDD capacity2000 GB
HDD interfaceSerial ATA
Maximum storage capacity16 TB
Number of HDDs supported2
Networking standardsIEEE 802.3af, IEEE 802.3at
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN (RJ-45) ports9
Supported network protocolsTCP/IP, DHCP, Hik-Connect, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP, HTTPS
Power over Ethernet (PoE) ports quantity8
Product colorBlack
Rack capacity1U
LED indicatorsLAN, Power, Status
AC input voltage100 - 240 V
Power consumption (typical)15 W
Total Power over Ethernet (PoE) budget80 W
Operating temperature (T-T)-10 - 55 °C
Operating relative humidity (H-H)10 - 90 %
Weight and Dimensions IconWeight and Dimensions
Depth315 mm
Width385 mm
Height52 mm
Weight3000 g

Related product manuals