Hilti TE 3000-AVR User Manual (English)

Other manuals for Hilti TE 3000-AVR

Instructions24 pages

Manual204 pages

Questions and Answers:

D
Daniel RomanJul 26, 2025
What to do if the service indicator blinks red on my Hilti TE 3000-AVR?
- B
  burtonchristopherJul 26, 2025
  If the service indicator on your Hilti Power Tool is blinking red, it could mean that the voltage from the power supply is too high. Try using a different power outlet and check the electrical supply. Alternatively, the overheating prevention cut-out may have been activated. In this case, allow the tool to cool down and clean the air vents. Note that running under no load is still possible.
K
kfloydJul 30, 2025
How to troubleshoot a Hilti Power Tool breaker that doesn’t start?
- P
  Paul BaileyJul 30, 2025
  There are several reasons why your Hilti Power Tool breaker might not start. It could be that the electronics are initializing, which can take up to 4 seconds after plugging it in, or that the electronic restart interlock has been activated after a power interruption. Try switching the power tool off and then on again. There might be an interruption in the power supply. Plug in another electric tool or appliance to check if it works. The generator might be in sleep mode. Apply a load to the generator by connecting a second power consumer, and switch the tool off and on again. The detachable supply cord might not be correctly fitted. Fit the detachable supply cord to the power tool correctly.
J
John LeeAug 3, 2025
Why is the service indicator light red on my Hilti Power Tool?
- C
  Cindy GillAug 3, 2025
  If the service indicator light on your Hilti Power Tool is red, it means the tool is faulty or servicing is due. Have the product repaired only by Hilti Service.
T
Tyler ClarkAug 8, 2025
Why doesn't my Hilti Power Hammer start?
- L
  Linda JohnsonAug 8, 2025
  If your Hilti Power Hammer doesn't start, it could be due to a few reasons. First, the electronics might be initializing, which can take up to 4 seconds, especially after a power interruption. In this case, switch the power tool off and then on again. Another cause could be an interruption in the electric supply. Try plugging in another electric tool or appliance to check if the outlet works. If you're using a generator, it might be in sleep mode; try applying a load by connecting another device like a worklight, then switch the tool off and on again. Finally, ensure the detachable supply cord is correctly fitted to the power tool.
M
Michael PollardAug 12, 2025
What to do if the service indicator blinks red on my Hilti Power Hammer?
- D
  David SheltonAug 12, 2025
  If the service indicator on your Hilti Power Hammer is blinking red, it could mean that the voltage from the electric supply is too high. Try using a different power outlet and check the electric supply. Alternatively, the overheating prevention cut-out might have been activated. In that case, allow the tool to cool down and clean the air vents. Note that running under no load is still possible.
M
Mr. Oscar Hall DDSAug 16, 2025
What does it mean when the service indicator light is red on my Hilti Power Hammer?
- H
  heather30Aug 17, 2025
  If the service indicator light on your Hilti Power Hammer is red, it means the tool is faulty or servicing is due. Have the product repaired only by Hilti Service.
F
Frank MurrayAug 21, 2025
How to fix no hammering action on a Hilti Power Hammer?
- L
  Lisa BrooksAug 21, 2025
  If your Hilti Power Hammer has no hammering action, it might be too cold. Bring the tip of the accessory tool into contact with the working surface, switch the power tool on, and let it run. Repeat this until the hammering mechanism starts working.

Hilti TE 3000-AVR Specifications

General

Impact energy	68 J
AVR	Yes
Voltage	230 V
Cord Length	4 m
Full hammering frequency	860 impacts/minute
Power source	Electric
Tool chuck type	TE-H
Chiseling application type	Heavy-duty
Frequency	50/60 Hz