HIMA HIMatrix F1 DI 16 01 - Decommissioning

42 pages

To Next Page

To Previous Page

7 Decommissioning F1 DI 16 01

Page 34 of 42 HI 800 153 E Rev. 2.00

7 Decommissioning

Remove the supply voltage to decommission the device. Afterwards pull out the pluggable

screw terminal connector blocks for inputs and outputs and the Ethernet cables.

Main Page

Table of Contents F11
Table of Contents3
Introduction5
Structure and Use of this Manual5
Table 1: Programming Tools for Himatrix Remote I/Os5
Target Audience6
Formatting Conventions7
Safety Notes7
Operating Tips8
Safety9
Intended Use9
Environmental Requirements9
ESD Protective Measures9
Table 3: Environmental Requirements9
Residual Risk10
Safety Precautions10
Emergency Information10
Product Description11
Safety Function11
Safety-Related Digital Inputs11
Figure 1: Connections to Safety-Related Digital Inputs11
Reaction in the Event of a Fault12
Line Control12
Figure 2: Line Control12
Equipment, Scope of Delivery13
IP Address and System ID (SRS)13
Type Label14
Figure 3: Sample Type Label14
Structure15
Figure 4: Front View15
Figure 5: Block Diagram15
LED Indicators16
Operating Voltage LED16
System Leds16
Table 5: Operating Voltage LED16
Table 6: System Leds16
Communication Leds17
I/O Leds17
Table 7: Ethernet Indicators17
Table 8: I/O Leds17
Communication18
Connections for Ethernet Communication18
Network Ports Used for Ethernet Communication18
Figure 6: Sample MAC Address Label18
Table 9 Ethernet Interfaces Properties18
Table 10: Network Ports in Use18
Pulsed Outputs19
Reset Key19
Product Data20
Product Data F1 DI 16 011 (-20 °C)20
Table 11: Product Data20
Table 12: Specifications for Digital Inputs20
Table 13: Specifications for the Pulsed Outputs20
Table 14: Product Data F1 DI 16 011 (-20 °C)20
Product Data F1 DI 16 01421
Certified Himatrix F1 DI 16 0121
Table 15: Product Data F1 DI 16 01421
Table 16: Certificates21
Start-Up22
Installation and Mounting22
Connecting the Digital Inputs22
Table 17: Terminal Assignment for the Digital Inputs22
Surges on Digital Inputs23
Connection of Digital Pulsed Outputs23
Table 18: Terminal Assignment for the Digital Pulsed Outputs23
Cable Plugs24
Table 19: Power Supply Cable Plug Properties24
Table 20: Input and Output Cable Plug Properties24
Mounting the F1 DI 16 01 in Zone 225
Figure 7: Label for Ex Conditions25
Configuration26
Configuration with Silworx26
Parameters and Error Codes for the Inputs and Outputs26
Digital Inputs F1 DI 16 0126
Tab Module27
Table 21: Silworx - System Parameters for Digital Inputs, Module Tab27
Tab DI 16: DO Channels28
Tab DI 16: DI Channels28
Table 22: Silworx - System Parameters for Pulsed Outputs, DI 16: DO Channels Tab28
Table 23: Silworx - System Parameters for Digital Inputs, DI 16: DI Channels Tab28
Configuration with ELOP II Factory29
Configuring the Inputs and Outputs29
Signals and Error Codes for the Inputs and Outputs29
Digital Inputs F1 DI 16 0130
Pulsed Outputs F1 DI 16 0131
Table 24: ELOP II Factory - Digital Input System Signals31
Table 25: ELOP II Factory - System Signals for the Pulsed Outputs31
Operation32
Handling32
Diagnosis32
Maintenance33
Faults33
Maintenance Measures33
Loading the Operating System33
Proof Test33
Decommissioning34
Transport35
Disposal36
Appendix37
Glossary37
Index of Figures38
Index of Tables39
Index40

HIMA HIMatrix F1 DI 16 01 - Decommissioning

Table of Contents

Other manuals for HIMA HIMatrix F1 DI 16 01

Related product manuals