Hitachi NEXT Series - Page 23

21
3. OPERATION PROCEDURE [How to Use the Liquid Crystal Display (LCD)]
Confirm the settings by lead/lag and multi unit control
(option). These options need wiring modification. Item
number with a dash “-“ cannot be selected on LCD
monitor.
1- MODE: Operation mode set on the digital monitor.
2. DUAL TIME: Alternate operation hours of lead/lag
operation.(Setting range : 0.1 to 99.9 hours; initial
value: 8.0)
3. METHOD: Switching method (overlap or interval)
of lead/lag operation.
4. SWITCHOVER: Switching-over or overlapping
period of lead/lag operation. (Setting range : 5 to 300
seconds; initial value: 15)
3.3.5 [FUNCTION MENU] - Setting Displays
㪲㪤㪬㪣㪫 㪠 㪄㪬㩷㪪㪜㪫㪫 㪠 㪥㪞㪴
㪈
㪤㪦㪛 㪜 䋺 㪞㪣
㪉䋮㪛㪬㪘㪣 㩷 㪫 㪠㪤㪜䋺 㩷 㪏䋮
㩷 㪪㪥
㪇㪿
㪊䋮㪤㪜㪫㪟㪦㪛 䋺 㪘㪧
㪋䋮㪪㪮 㪠 㪫㪚㪟㪦㪭㪜㪩䋺 㪇 㪈 㪌 㫊
㪌䋮㪙㪘㪚㪢㪬㪧䋺 㪎㫇
㪦㪭㪩㪩㪣
㫊㫀
㪍䋮㪬㪥㪣㪦㪘㪛 䋺 㪊㫇 㫊 㫀
㪎
㪘㪣㪫䋮㪫 㪠㪤㪜䋺㩷 㪋㪏㪇㪤㪠㪥
㪏
㪚㪦㪥㪫㪩㪦㪣 㪤㪦㪛㪜 䋺 㪙
㪪㪜㪫䋺㪪㪫㪦㪩㪜 㩷㪤㪦㪥䋺㪙㪘㪚㪢
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
㪲㪙㪘㪪㪠㪚 㪪㪜㪫㪬㪧㪴
㪭㪜㪩䋮䋺 㪎䋮㪌
㪍䋮㪋
㪪㪜㪩 㪠 㪜㪪 㪥㪘㪤㪜䋺 㪛㪪㪧
㪚㪦㪦㪣 㪠 㪥㪞 㪤㪜 㪫㪟㪦㪛䋺 㪮㪫㪩
㪥㪦䋮㪦㪝 㪪㪫㪘㪞㪜 䋺 㩷 㪉
㪧㪄㪪㪧㪜㪚䋺 㪈 㪇 㪉㫇 㫊 㫀
㪧䋮㪛㪘 㪫 㪘 䋺 㪍 㪏㫇 㫊 㫀
䌃䌔䋺 㪉㪌㪇䌁
㪚㪣 㪫䋮㪛㪜 㪣㪘㪰 䋺 㩷 㪌 㫊
㪠㪧㪠䋺 㪠㪠㪠
㪘㪛㪩㪜 㪪㪪 㪥㪦䋮 䋺 㩷 㪈
㪤㪦㪥 䋺 㪙㪘㪚㪢
If using the backup function, switch to the digital
monitor for setting.
This display contains software version (VER.), air compressor
series (SERIES NAME), cooling method (COOLING
METHOD), number of air compression stages (NO. OF
STAGE), action against instantaneous power interruption
(IPI) and etc. “＊＊” means the setting that is not required.
① Indicates board software version.
② Indicates compressor type.
③ Displays cooling type.
④ Displays the number of compressor stages.
⑤
Displays pressure specification.
⑥ Displays interstage pressure.
⑦ Indicates CT setting value.
⑧ Displays water failure detection conditions for water
cooled compressor.
⑨ Displays status of instantaneous power interruption
(IPI) restart setting.
⑩
Displays compressor number. (Must be distinguished
by number is using communication function.)
When contacting the local Hitachi distributor, inform this
information as a based setting status.
IMPORTANT
IMPORTANT
The settings can be memorized while the air compressor
is stopped.
IMPORTANT
5. BACKUP: Pressure to start a backup unit in a backup
operation (cut-in (load) pressure – α)
6. UNLOAD: Pressure to unload both the units in a
backup operation (cut-out (unload) pressure – α)
7- ALT. TIME: Displays time remaining until switch for
dual / backup operation. Time is not counted down
when operating 2 units for backup operation. When
operation is stopped, remaining time is maintained.
8- CONTROL MODE: Control mode A or B for Vtype
(
3.3.2). “＊＊” is indicated in fixed speed type.
SNGL Operates a air compressor independently
STPR
Operates by multi roller EX of exclusive use for NEXT
series using communication function.
By this setting RS485 communication port is effective.
The setting of air compressor number is required.
DUAL
Operates two air compressors alternately according to
a time schedule. The AUTO light comes ON (glowing).
BKUP
Operates two air compressors according to a preset
back up pressure. Starts the back up slave unit when
the pressure has dropped to the desired preset back up
pressure. The AUTO light comes ON (glowing)
OVERLAP
Slave unit starts, master/slave units overlap in operation
for a preset period, and then master unit stops.
INTERVAL
Master unit stops, a non-operating interval passes, and
then slave unit starts.
1
Model Setting Confirmation
2
Operation Mode Setting