What does Excessively low pressure difference mean on Hitachi Air Conditioner?
If your Hitachi Air Conditioner displays 'Excessively low pressure difference', check for proper pressure differences in the system. The system stops after P11 retry due to pressure ratio being less than 1.8 for 3 minutes.
What causes Hitachi YUTAKI S80 Air Conditioner hydraulic alarm pressure?
If your Hitachi Air Conditioner displays 'Hydraulic alarm pressure', check the system for any leaks or blockages affecting water pressure. This alarm indicates that water pressure is not detected in the hydraulic cycle.
What to do if Hitachi YUTAKI S80 has Receiver Communication failure?
If your Hitachi Air Conditioner is not receiving a signal, check the Opentherm/Hlink connection.
How to fix Incorrect PCB Setting in Hitachi Air Conditioner?
If your Hitachi Air Conditioner shows 'Incorrect PCB Setting', correct the DSW settings. This issue is caused by a wrong DSW setting in the case of Co041.
How to correct Hitachi YUTAKI S80 Air Conditioner incorrect indoor unit number setting?
If your Hitachi Air Conditioner displays 'Incorrect indoor unit number setting', correct the indoor unit number settings. This issue can be caused by duplication of indoor unit numbers or the number of indoor units exceeding specifications.
How do I fix a 'Unit Capacity setting Error' on my Hitachi YUTAKI S80?
If your Hitachi Air Conditioner displays a 'Unit Capacity setting Error', ensure correct capacity settings for both indoor and outdoor units. This error indicates a mismatch between the indoor and outdoor unit capacities.
How to fix Hitachi Air Conditioner activation of overcurrent protection?
If your Hitachi Air Conditioner activates overcurrent protection, inspect the inverter PCB and compressor operation. This can be caused by overload, overcurrent, failure of the Inverter PCB, a clogged heat exchanger, a locked compressor, or EVI/EVO failure.
What to do if Hitachi YUTAKI S80 shows Thermostat Heater Alarm?
If your Hitachi Air Conditioner is showing a high temperature in the electric heater, check the electric heater for proper operation.
How to troubleshoot Hitachi Air Conditioner hydraulic alarm flow and water pump malfunction?
If your Hitachi Air Conditioner displays a hydraulic alarm related to flow and water pump malfunction, check the water pump for proper operation and repair or replace it if defective. This alarm indicates that water flow is not detected in the hydraulic cycle or the pump is defective.
What causes Hitachi YUTAKI S80 to activate safety device from excessively low suction pressure?
If your Hitachi Air Conditioner activates the safety device from excessively low suction pressure, inspect refrigerant levels and piping for blockages. This issue is often due to a shortage or leakage of refrigerant, piping clogging, a closed expansion valve, or a locked fan motor.
General| Refrigerant | R32 |
|---|---|
| Type | Air-to-Water Heat Pump |
| Operating Temperature Range (Heating) | -20°C to 35°C |
| Operating Temperature Range (Cooling) | 10°C to 46°C |
| Sound Power Level | Data varies significantly depending on the specific indoor and outdoor unit models. Please refer to the specific model's datasheet. |
| Noise Level (Indoor Unit) | Data varies significantly depending on the specific indoor unit model. Please refer to the specific model's datasheet. |
| Noise Level (Outdoor Unit) | Data varies significantly depending on the specific outdoor unit model. Please refer to the specific model's datasheet. |
| Power Supply | 50Hz |
| Dimensions (Indoor Unit) | Data varies significantly depending on the specific indoor unit model. Please refer to the specific model's datasheet. |
| Dimensions (Outdoor Unit) | Data varies significantly depending on the specific outdoor unit model. Please refer to the specific model's datasheet. |
| Weight (Indoor Unit) | Data varies significantly depending on the specific indoor unit model. Please refer to the specific model's datasheet. |
| Weight (Outdoor Unit) | Data varies significantly depending on the specific outdoor unit model. Please refer to the specific model's datasheet. |
Crucial safety warnings and instructions for correct installation and operation.
Highlights critical instructions for manual adherence, specifications, and system integrity.
Details Energy-related Product (ERP) performance data for space heaters, efficiency, and energy classes.
Illustrates refrigerant and hydraulic circuits for YUTAKI S and S COMBI split systems.
Outlines safety measures and concentration limits for refrigerant leaks.
Lists indoor unit alarm codes, their origin, details of abnormality, and main troubleshooting factors.
Details outdoor unit alarm codes, categories, types of abnormality, and their main causes.
To Next Page
