EasyManuals Logo

Holtek HT66F30 User Manual

Default Icon
294 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #123 background imageLoading...
Page #123 background image
Rev. 2.50 122 June 22, 2017 Rev. 2.50 123 June 22, 2017
HT66F20/HT66F30/HT66F40/HT66F50/HT66F60
HT66FU30/HT66FU40/HT66FU50/HT66FU60
A/D Flash MCU with EEPROM
HT66F20/HT66F30/HT66F40/HT66F50/HT66F60
HT66FU30/HT66FU40/HT66FU50/HT66FU60
A/D Flash MCU with EEPROM
Standard Type TM – STM
TheStandardTypeTMcontainsveoperatingmodes,whichareCompareMatchOutput,Timer/
EventCounter,CaptureInput,SinglePulseOutputandPWMOutputmodes.TheStandardTMcan
alsobecontrolledwithanexternalinputpinandcandrivetwoexternaloutputpins.
STM Name TM No. TM Input Pin TM Output Pin
HT66F20
10-bit STM 1 TCK1 TP1_0, TP1_1
HT66F30
HT66F40
16-bit STM 2 TCK2 TP2_0, TP2_1
HT66F50 16-bit STM 2 TCK2 TP2_0, TP2_1
HT66F60 16-bit STM 2 TCK2 TP2_0, TP2_1



  
 



 
  
 

  
    
  
  

 



 
  

  


 

 



 













 
Standard Type TM Block Diagram
Standard TM Operation
TherearetwosizesofStandardTMs,oneis10-bitswideandtheotheris16-bitswide.Atthecoreis
a10or16-bitcount-upcounterwhichisdrivenbyauserselectableinternalorexternalclocksource.
Therearealsotwointernalcomparatorswiththenames,ComparatorAandComparatorP.These
comparatorswillcomparethevalueinthecounterwithCCRPandCCRAregisters.TheCCRP
comparatoris3or8-bitswidewhosevalueiscomparedthewithhighest3or8bitsinthecounter
whiletheCCRAisthetenorsixteenbitsandthereforecomparesallcounterbits.
Theonlywayofchangingthevalueofthe10or16-bitcounterusingtheapplicationprogram,is
toclearthecounterbychangingtheTnONbitfromlowtohigh.Thecounterwillalsobecleared
automaticallybyacounteroveroworacomparematchwithoneofitsassociatedcomparators.
Whentheseconditionsoccur,aTMinterruptsignalwillalsousuallybegenerated.TheStandard
TypeTMcanoperateinanumberofdifferentoperationalmodes,canbedrivenbydifferentclock
sourcesincludinganinputpinandcanalsocontrolanoutputpin.Alloperatingsetupconditionsare
selectedusingrelevantinternalregisters.

Table of Contents

Other manuals for Holtek HT66F30

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Holtek HT66F30 and is the answer not in the manual?

Holtek HT66F30 Specifications

General IconGeneral
BrandHoltek
ModelHT66F30
CategoryComputer Hardware
LanguageEnglish

Related product manuals