Honeywell 7847i-E - Page 18

7847i-E Installation and Setup Guide
3-6
PROMPTS
ENTRY
OPTIONS
DESCRIPTION
30
Zn6 Trigger Type
(V+)_
• (V+)
• (V–)
• (EOLR)
Selects the triggering method for this zone input.
Press the [space] key to scroll through choices.
UL: V+ must be set as inverted and V- as non-inverted
31
Invert Zn6 Y/N
(N)_
[Y], [N]
Inverts the alarm and normal states of the zone 6 trigger;
otherwise uses normal input signal.
32
Restore Zn6 Y/N
(Y)_
[Y], [N]
Enables restore reporting for zone 6.
33
Delay Zn6 (secs)
(00)_
[01-15]
[00] = no delay
Defines the reporting delay in seconds for zone 6.
UL:
Must be 00
34
Enable Zn7 Y/N
(N)_
[Y], [N]
Enables alarm reporting for zone 7.
If [N], skip to Prompt 47: "Use DHCP."
35
Zn7 Trigger Type
(V)_
• (V+)
• (V–)
• (EOLR)
Selects the triggering method for this zone input.
Press the [space] key to scroll choices.
UL: V+ must be set as inverted and V- as non-inverted
36
Invert Zn7 Y/N
(N)_
[Y], [N]
Inverts the alarm and normal states of the zone 7 trigger;
otherwise, uses normal input signal.
37
Restore Zn7 Y/N
(Y)_
[Y], [N]
Enables restore reporting for zone 7.
38
Delay Zn7 (secs)
(00)_
[01-15]
[00] = no delay
Defines the reporting delay in seconds for zone 7.
UL: Must be 00
39
Use DHCP Y/N
(Y)_
[Y], [N]
Dynamically allocates the IP addresses (recommended);
then skip to Prompt 43: "Review?"
If [N], uses fixed IP addresses.
40
NIC IP Address:
255.255.255.255_
12 digit:
xxx.xxx.xxx.xxx
Enter the 4-part address for this device. The four parts of
the address must be separated by spaces (displayed as
periods in Review mode).
49
Subnet Mask:
255.255.255.255_
12 digit:
xxx.xxx.xxx.xxx
Enter the 32-bit address mask used to indicate the portion
(bits) of the IP address that is being used for the subnet
address. The four parts of the address must be separated
by spaces (displayed as periods in Review mode).
41
Gateway IP Addr:
255.255.255.255_
12 digit:
xxx.xxx.xxx.xxx
Enter the 4-part address assigned to the Gateway. The
four parts of the address must be separated by spaces
(displayed as periods in Review mode).
42
DNS Serv IP Addr:
255.255.255.255_
12 digit:
xxx.xxx.xxx.xxx
Enter the 4-part IP address assigned to the DNS (Domain
Name System) server. The four parts of the address must
be separated by spaces (displayed as periods in Review
mode).
43
Review? Y/N
[Y] = review
[N] = exit
Reviewing Programming Mode Entries
To review the programming options (to ensure that the
correct entries have been made), press [Y]. The
programming prompts are displayed again. Use the
up/down arrow keys to scroll through the program fields
without changing any of the values. If a value requires
change, simply type in the correct value. When the last
field is displayed, the “REVIEW?” prompt again appears.
To exit the programming mode, press [N] in response to
the "REVIEW?" prompt, and refer to Exiting Programming
Mode at the end of this section.