About Descriptor Programming (*82 Menu Mode)
The system lets you directly enter zone descriptors for each protection zone so when an alarm or trouble
occurs in a zone, an appropriate description for that zone's location can be displayed at the keypad. Each
description is composed of up to 16 characters. In addition, three custom words can be programmed as
partition descriptors, each composed of up to 10 characters.
NOTE: You can also enter zone descriptors when the zone is being defined in
✱
56 Menu mode.
When defining descriptors:
• Pressing the [4] key moves cursor one space to the left.
• Pressing the [6] key accepts the entry and moves the cursor to the next position.
• Pressing the [8] key saves the entered descriptor and moves to the next descriptor.
Start Zone Descriptor Programming mode by pressing *82 while in Data Programming mode.
PROMPT
VALID ENTRIES EXPLANATION
Program Alpha ?
0=No, 1=Yes 00
Program Alpha
0 = no
1 = yes
[∗] to continue
The “Program Alpha ?” prompt will appear.
Press 1 to program zone descriptors or partition descriptors.
Press 0 to exit.
Sel Zone Des=0
Part = 1
Select Descriptor Type
(Zone Descriptor or Partition
Descriptor)
0 = create zone descriptors (see
Zone No? prompt below)
1 = create partition descriptors
[∗] to continue
Custom Word Numbers:
11 = partition 1 descriptor
12 = partition 2 descriptor
13 = partition 3 descriptor
This prompt selects whether you are entering zone descriptors or
entering partition descriptors.
Pressing [0] goes to the next prompt to let you enter zone descriptors.
Pressing [1] lets you program a partition descriptor. If selected, the
following prompt appears:
PART?
Enter the 2-digit custom word number (11-13) to be programmed,
then press [∗].
Enter the descriptor as described in steps 1-3 in the Zone Number
section below.
Zone No.? 00
Zone Number
Enter the desired zone number.
[∗] to continue.
After pressing [∗], a cursor will appear at the second line.
1. Refer to the Character Chart below.
Press [#], followed by the 3-digit entry for the first letter you
want to display (e.g., # 0 6 5 for “A”).
Press [6] to move the cursor to the right.
2. Repeat Step 1 to enter the next characters until the desired
descriptor is entered. Zone descriptors can be up to a maximum
of 16 characters. Partition descriptors can be up to a maximum
of 10 characters. You can use the [4] key to move the cursor to
the left, if necessary.
3. When done, press the [8] key to save the descriptor and return
to the “Zone No. ?” prompt.
4. Enter the zone number for the next descriptor, press [∗], and
repeat steps 1-3. To change a custom word (partition descriptor),
simply overwrite it.
To exit, enter zone number “00.”
––––––––––––––––––––––––––––––– CHARACTER (ASCII) CHART –––––––––––––––––––––––––––––––
032(space)
033 = !
034 = "
035 = #
036 = $
037 = %
038 = &
039 = '
040 = (
041 = )
042 = *
043 = +
044 = ,
045 = –
046 = .
047 = /
048 = 0
049 = 1
050 = 2
051 = 3
052 = 4
053 = 5
054 = 6
055 = 7
056 = 8
057 = 9
058 = :
059 = ;
060 = <
061 = =
062 = >
063 = ?
064 = @
065 = A
066 = B
067 = C
068 = D
069 = E
070 = F
071 = G
072 = H
073 = I
074 = J
075 = K
076 = L
077 = M
078 = N
079 = O
080 = P
081 = Q
082 = R
083 = S
084 = T
085 = U
086 = V
087 = W
088 = X
089 = Y
090 = Z
091 = [
092 = ¥
093 = ]
094 = ^
095 = _
096 = `
097 = a
098 = b
099 = c
100 = d
101 = e
102 = f
103 = g
104 = h
105 = i
106 = j
107 = k
108 = l
109 = m
110 = n
111 = o
112 = p
113 = q
114 = r
115 = s
116 = t
117 = u
118 = v
119 = w
120 = x
121 = y
122 = z
123 = {
124 = |
125 = }
126 = →
127 = ←
5-15
To Next Page
Loading...
