Honeywell LYNX Touch User Manual

– 20 –
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES
SECURING THE PREMISES
Arming the System
Use this mode when no one will be staying on the premises. Close all protected perimeter
windows and doors before arming. The green READY indicator on the control should be lit if
the system is ready to be armed. When armed in AWAY mode, the system will sound an
alarm if a protected door or window is opened, or if any movement is detected inside the
premises, when infrared detection devices are used. You may leave through a designated
entrance door during the exit delay period without causing an alarm. You may also re-enter
through the entrance door, but you must disarm the system within the entry delay period or
an alarm will occur.
If Quick Arm was programmed by the installer, you do not need to enter
the security code to arm the system. The security code must always be used to disarm the
system, however.
❂ ❃ Ô ❄ ❅ ❆ ❇ ❈ ❉ Ó Ó Ô ❊ ❋ Ò ● Ô ❅ ❍ ● ■ ❍ ❈ Ó ❅ ❏ ❏ Ô ❊ ❋ Ò ● Ô ❑ ❅ ❍ ❍ Ò Ó ● ❉ ❈ ❅ ❊ ▲ Ó ❃ Ô ❈ ❇ ❈ Ó Ô ▲ ▼ ❍ ❏ Ô ❈ ❈ ❉ Ó ◆ ❅ ❈ ▼ ❈ Ô ● Ó Ò ❅ ❊ ▲
Ó ❃ Ô ❈ ❇ ❈ Ó Ô ▲ ❖ ■ ❍ ❅ ● ● ❉ Ó ❉ Ò ❍ P ❉ ◗ Ó ❃ Ô ❈ ❇ ❈ Ó Ô ▲ ❉ ❈ ❅ ❊ ▲ Ô ● ❆ ❇ ❘ ❊ Ô ❈ ❈ ❉ ❍ ❙ ❚ ❉ ❅ ❯ ▼ ❉ ❑ ❱ ❲ Ö ❊ ▲ ❉ ❍ ❙ P ❍ Ô ❉ Ó ❃ Ô ❊ Ó ❃ Ô
❄ ❅ ❆ ❇ ❈ ❉ Ó Ó Ô ❊ ❋ Ò ● Ô ❍ Ò ❊ ■ ❍ ❈ Ó ❅ ❏ ❏ Ô ❊ ❋ Ò ● Ô ❑ ❅ ❍ ● ❉ ❈ ❅ ❊ ▲ Ó ❃ Ô ❈ ❇ ❈ Ó Ô ▲ ❖
æ ç è é ê
ë ì í ë î ï ð
ñ ò ó ô õ ö ÷ ø ù ú
ë ì í û ü ï ð
ý ç ì éþ é ÿ ï ð
 ✁ ç è é
✂ ✄ ☎ ✂ ✆ ✝ ✞ ✟ ✠ ✡ ☛ ✆ ☞ ✌ ✄ ✂ ✄
✍ ✎ ✎ ✎ ✏ ✑ ✎ ✎ ✏ ✎ ✎ ✒ ✏ ✓ ✎
ý é ê ê ï ✔ é
û ð ê ü é í
1. Select the Arm Away icon, the system will
beep once and display a keypad.
✕ ✖ ✗ ✘ ✙ ✚ ✛ ✜ ✢ ✣
✤ ✥ ✦ ✧ ★ ✩ ✪ ✫ ✪ ✧ ✩ ✦ ✬ ✭ ✤ ✮ ✯ ✫ ✦ ✰ ✱ ✩
✲ ✳ ✴ ✵ ✶ ✷ ✸ ✹ ✵ ✺
✻ ✼ ✽ ✾ ✿ ❀
❁ ❂❃
❄ ❅
❆
❇
❈ ❉
❊
✻ ❀ ✿ ✼ ❋
● ❍ ❍ ❍ ■ ❏ ❍ ❍ ■ ❍ ● ❑ ■ ▲ ❍
2. Enter a valid User Code.
OR
If Quick Arm has been enabled, select the
➚
Quick Arm
➪
icon.
The system will beep two times and announce
➶
Armed Away Exit Now . The exit delay screen
will be displayed. If programmed the display
will count down the time remaining in the exit
delay in seconds.
▼ ◆ ❖ P ◗
If a valid user code is not entered or the Confirm
icon has not been selected within 10 seconds,
the system will return to the
❘
home
❙
screen and it
will not be armed.

Honeywell LYNX Touch Specifications

General

Zones	Up to 64 wireless zones
Voice Control	No
Remote Control	Yes, via mobile app
Keypad Zones	No
Partitions	No
Voice Prompts	Yes
Built-in Z-Wave	Yes
Display	Color touchscreen
Communication	Cellular
Wireless Zones	64
Automation	Z-Wave
Siren Output	Built-in
Wireless Frequency	345 MHz
Supported Security Devices	Door/window sensors, motion detectors
Compatibility	Honeywell 5800 series wireless devices