Honeywell Notifier ACPS-610/E - 1.7 LED Indicators

12 ACPS-610/E Manual — P/N 53018:A1 07/31/2007
Introduction LED Indicators
1.7 LED Indicators
There are 21 LEDs that indicate various conditions and troubles. The following table lists and
describes each. Figure 1.2 on page 13 shows the location of the LEDs on the PC boards.
Reference LED Name Color Description
Main
Control
Unit
2STATUS
*
Green
Slow blink (1x/sec.) during normal operation.
3 RESET Yellow
Illuminates during on Power Up and ACPS-610 CPU reset. Blinking
reset indicates trouble, call technical service.
4GEN TBL*Yellow
Steady glow indicates trouble, except as noted below:
• Slow blink (1x/sec.)................................SLC Address Out of Range
• Fast blink (5x/sec.) ................................................... Program Mode
• 1 blink, pause and repeat ........... KAPS-24 Communication Failure
• 2 blinks, pause and repeat ...........................UZC Sync Signal Loss
5 SLCRX Green
Blinks when data is received from the SLC.
6 SLCTX Green
Blinks when data is transmitted to the SLC.
7 OUT1 TBL* Yellow • Steady.......................................................................In Current Limit
• Steady (with fast blinking GEN TBL) .....................RAM Test Failure
– Call Technical Service.
• Fast blink (5x/sec.) ..............................................Hardware Failure
†
• 1 blink, pause and repeat ....................................................... Open
• 2 blinks, pause and repeat .......................................................Short
8,9 OUT1 Active Green/Red Glows green when output is active +24V power.
Glows red when output is active NAC.
10 OUT2 TBL* Yellow • Steady.......................................................................In Current Limit
• Steady (with fast blinking GEN TBL) ............. Revision ID Mismatch
– Download compatible firmware (see page 30).
• Fast blink (5x/sec.) ..............................................Hardware Failure
†
• 1 blink, pause and repeat ....................................................... Open
• 2 blinks, pause and repeat .......................................................Short
11, 12 OUT2 Active Green/Red
Glows green when output is +24V power.
Glows red when output is active NAC.
13 OUT3 TBL* Yellow • Steady......................................................................In Current Limit.
• Steady (with fast blinking GEN TBL) ..................Corrupt Application
– Download application (see page 30).
• Fast blink (5x/sec.) ..............................................Hardware Failure
†
• 1 blink, pause and repeat ....................................................... Open
• 2 blinks, pause and repeat .......................................................Short
14, 15 OUT3 Active Green/Red Glows green when output is active +24V power.
Glows red when output is active NAC.
16 OUT4 TBL* Yellow • Steady.......................................................................In Current Limit
• Steady (with fast blinking GEN TBL) ....................Corrupt Database
– Download database (see page 30).
• Fast blink (5x/sec.) ..............................................Hardware Failure
†
• 1 blink, pause and repeat ....................................................... Open
• 2 blinks, pause and repeat .......................................................Short
17, 18 OUT4 Active Green/Red Glows green when output is active +24V power.
Glows red when output is active NAC.
KAPS-24
1 Logic Power Green
Illuminates when logic power is active (Normal condition).
2TRBLYellow
Blinks, pauses and repeats; as specified below, when the following
troubles occur:
– AC Failure.......................................................................1 blink
– High Battery....................................................................2 blinks
– Low Battery.....................................................................3 blinks
– Charger Failure...............................................................4 blinks
3 EARTH FAULT Yellow Illuminates when a ground fault is detected.
4 AC Green
Illuminates when there is AC power.
Table 1.2 LED Indicators
* STATUS, GENERAL and OUTPUT TROUBLE LEDS steady when database/firmware download is in process. Do not disconnect power or the
USB cable during this time!
† Disconnect the output and wait for 10 seconds. Then, reset the Power Supply by disconnecting the battery and AC power. If the problem
persists, replace the ACPS-610.