What to do if my Honeywell Barcode Reader has no LEDs, beeper, or motor spin?
If your Honeywell Barcode Reader shows no LEDs, beeper, or motor spin, it indicates that the scanner isn't receiving power. Check the transformer, outlet, and power strip to ensure they are functioning correctly. Also, verify that the cable is securely plugged into the scanner.
Why is the data transmitted to the host incorrect when my Honeywell Orbit MS7120 scans?
If your Honeywell Barcode Reader scans, but the data transmitted to the host is incorrect, the scanner’s data format may not match the host system requirements. Verify that the scanner’s data format matches the format required by the host and ensure that the scanner is connected to the proper host port.
What to do if my Honeywell Barcode Reader powers up and scans but doesn't communicate with the host?
If your Honeywell Barcode Reader powers up and scans but doesn't communicate properly to the host, the com port at the host might not be working or configured properly. Check to make sure that the baud rate and parity of the scanner and the communication port match and that the program is looking for RS232 data.
What to do if my Honeywell Orbit MS7120 scans a barcode then locks up?
If your Honeywell Barcode Reader scans a bar code but locks up after the first scan, it's likely that the scanner is configured to support some form of host handshaking but isn't receiving the signal. If the scanner is set up to support ACK/NAK, RTS/CTS, XON/XOFF or D/E, verify that the host cable and host are supporting the handshaking properly.
Why does my Honeywell Barcode Reader power up but not scan or beep?
If your Honeywell Barcode Reader powers up but does not scan and/or beep, the unit may be trying to scan a particular symbology that is not enabled. UPC/EAN, Code 39, Interleaved 2 of 5, Code 93, Code 128 and Codabar are enabled by default. Verify that the type of bar code being read has been selected. Also, the scanner could be configured for a character length lock, or a minimum length, and the scanned bar code does not meet the configured criteria. Verify that the bar code that is being scanned falls into the criteria, as the scanner defaults to a minimum of four character bar code.
Why is the data received by the host incorrect from my Honeywell Orbit MS7120?
If the host is receiving data from your Honeywell Barcode Reader, but the data doesn't look correct, the scanner and host may not be configured for the same interface. Check that the scanner and the host are configured for the same interface.
What to do if my Honeywell Orbit MS7120 Barcode Reader scans but the data is not correct?
If your Honeywell Barcode Reader scans but the data is not correct, the unit may not be configured correctly. Make sure that the proper PC type (i.e., AT or PS2) is selected. Also, verify correct country code and data formatting are selected and adjust the inter-scan delay.
Why does my Honeywell Barcode Reader have no LEDs and/or beeper?
If your Honeywell Barcode Reader has no LEDs and/or beeper, it could be that no power is being supplied to the scanner from the host. Some host systems cannot supply enough current to power the Orbit. Use the power supply included with the scanner.
Why does my Honeywell Orbit MS7120 Barcode Reader beep for some barcodes but not others of the same type?
If your Honeywell Barcode Reader beeps for some barcodes but not others of the same symbology, the bar code may have been printed incorrectly. Check if it is a check digit, character or border problem. Also, the scanner may not be configured correctly for the type of bar code, so check if check digits are set properly. Finally, the minimum symbol length setting might not work with the bar code, so check if the correct minimum symbol length is set.
What to do if my Honeywell Orbit MS7120 is not transmitting each character?
If your Honeywell Barcode Reader is not transmitting each character, the unit may not be configured correctly. Increase the inter-scan code delay setting. Adjust whether the F0 break is transmitted. It may be necessary to try both settings.
Instructions for connecting the scanner using RS232 or Light Pen interfaces.
Guide for connecting the scanner via a keyboard wedge interface.
Details the installation process for USB connections.
Outlines specific LED and beep patterns indicating scanner malfunctions.
Shows connector types and pin functions for host-side connections.
Provides crucial safety warnings regarding laser exposure and device usage.
Covers Electromagnetic Compatibility standards and compliance for Class A/B devices.
Provides contact information for technical support across different regions.
General| Wavelength | 650 nm |
|---|---|
| Scanner type | 1D |
| Light levels (direct sunlight) | 0 - 4842 lx |
| Bluetooth | No |
| Standard interfaces | USB |
| Input voltage | 5 V |
| Product color | Black |
| Storage temperature (T-T) | -40 - 60 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 5 - 95 % |
| Harmonized System (HS) code | 84716070 |
Weight and Dimensions| Depth | 105 mm |
|---|---|
| Width | 102 mm |
| Height | 150 mm |
| Weight | 400 g |
To Next Page
