13 14

1 2

1. INTRODUCTION

SensePoint is for the detection of toxic gases and is

designed for use with an approved junction box.

It employs an electrochemical cell sensor device which is

gas specic and used as part of a 4-20mA loop powered

measuring circuit. The sensor includes a voltage clamp

within a sealed Exd enclosure and an electrochemical cell

driver and cell within an IS portion of the sensor.

Different sensor versions detect different gases. Sensors

are available for the detection of H

S, CO, CI

, NH

, H

, SO

NO, NO

, O

. The sensor is available in M20* or 3/4 NPT

thread versions. All accept accessories from the specied

range. Should you require information outside the scope of

these instructions please contact Honeywell Analytics Ltd.

This product is certied for use in hazardous areas and is

protected against water and dust ingress to IP65, or IP66/67

if approved weather protection is tted.

*NOTE - M20 thread option awaiting certication.

2. ASSOCIATED DOCUMENTATION

2106M0502 SensePoint Technical Handbook.

Refer to the relevant control system manual for connection

information.

1. INTRODUCTION & 2. ASSOCIATED DOCUMENTATIONCONTENTS

1. INTRODUCTION .........................................................2

2. ASSOCIATED DOCUMENTATION ..............................2

3. SAFETY ......................................................................3

3.1 Warnings ...........................................................3

3.2 Precautions .......................................................3

4. OPERATIONS .............................................................4

4.1 Installation ........................................................4

4.2 Calibration.........................................................5

4.3 Fault nding ......................................................8

5. MAINTENANCE ..........................................................9

5.1 Changing the electrochemical cell and

internal lter ......................................................9

5.2 Changing the external hydrophobic assembly . 10

Appendix A - Specications .............................. 11

Appendix B - Glossary ......................................12

Appendix C - Main features............................... 13

Appendix D - Spare parts .................................. 14

APPENDIX A - SPECIFICATIONS APPENDIX B - GLOSSARY APPENDIX C - MAIN FEATURES APPENDIX D - SPARE PARTS

Operating temperature range:

see table 1.

Operating humidity range:

20% to 90% RH continuous.

10% to 99% RH intermittent - non condensing.

Operating pressure range:

90 to 110 k Pa.

Warm up time:

see table 1.

Voltage range:

18 to 30 V at sensor.

Power consumption:

0.9 W Max.

Signal output:

4 to 20 mA loop powered.

Calibration ow rate:

recommended between 0.5 and 1.5 l/min.

Expected operating life:

S, CO, no less than 24 months.

, Cl

, H

, SO

, NO

, NO, O

no less than 12 months.

IP rating:

IP65 standard.

IP66/67 when tted with appropriate weather protection.

Certication:

Ex II 2G EEx dia IIC T4 -55 to +65°C.

Sensepoint 2106AXXXX (Tox).

Vmax 32V BAS98ATEX2157X.

UL approved via IEC 79 (pending).

This product complies with the relevant CE standards

concerning performance: EMC to BS EN50081 parts 1 & 2,

BS EN50082 parts 1 & 2 and EN 45544.

Exd

Flame proof or explosion proof within the connes of European

standards EN50014 and EN50018. An enclosure that can

withstand the pressure developed during the internal explosion

of an explosive mixture and which prevents transmission of

the explosion to the explosive atmosphere surrounding the

enclosure.

Exe

Increased safety within the connes of European standards

EN50014 and EN50019 applied to electrical apparatus that

does not produce arcs or sparks in normal service, in which

additional measures are applied so as to give increased

security against the possibility of excessive temperatures.

PPS

Polymer polyphenylene sulphide, suitable for use in most

chemical environments (eg acids, aldehydes, ketones,

alkalies, petroleum, aromatic hydrocarbons, alcohols, ethers,

esters and most chlorinated hydrocarbons). Avoid immersion

in solvents for extended periods. For further details contact

Honeywell Analytics Ltd.

Intrinsically safe, apparatus in which the circuits themselves

are incapable of causing ignition of a ammable gas.

Replacement sensing elements (including hydrophobic barrier):

gas type replacement cell

2106B1545

2106B1546

2106B1547

CO 2106B1548

S 2106B1549

NO 2106B1594

(1000ppm) 2106B1595

(50ppm) 2106B1596

(1000ppm) 2106B1597

(10000ppm) 2106B1598

2106B1599

Weather protection .........................................02000-A-1635

Flow housing (standard) .................................02000-A-1645

Flow housing (for adsorbent gases) ................02000-A-3120

Junction box (standard) ..................................00780-A-0100

To reorder a complete new sensor, see the label on the product

leads, or contact Honeywell Analytics Ltd.

103mm

Standard Honeywell

Analytics junction box

threads available:

M20*; 3/4” NPT.

SensePoint Toxic

Gas Sensor

Weight - 185g

(205g oxygen)

External Hydrophobic barrier

Plastic retainer

103mm

90mm

56mm

52mm

(across ats)

Exe/Exd gland

optional

(recommended

for harsh/dirty

environments)

Poole Dorset

SensePoint

static risk - read manual

EEx d ia IIC T4 Tamb -55 +65

0600

Bas98ATEX2157X II 2G

manufacturer’s

trademark &

address

CE mark

- conforms to

all applicable

European

directives

product name

test house

trademark

certication code

as EN50014 1992

certication number

certied ambient

temperature

range

explosion

protection mark

and equipment

group & category

ident.

number

of ATEX

notied

body

caution

Certication label as dened in directive 94/9/EC

Ser.No./year of manufacture

Operating Instructions

Sensepoint

Toxic Sensor

Contact Honeywell Analytics:

Find out more

www.honeywellanalytics.com

Europe, Middle East, Africa, India

Life Safety Distribution AG

Wilstrasse 11-U31

CH-8610 Uster

Switzerland

Tel: +41 (0)44 943 4300

Fax: +41 (0)44 943 4398

gasdetection@honeywell.com

Americas

Honeywell Analytics Inc.

405 Barclay Blvd.

Lincolnshire, IL 60069

USA

Tel: +1 847 955 8200

Toll free: +1 800 538 0363

Fax: +1 847 955 8208

detectgas@honeywell.com

www.honeywell.com

Technical Services

ha.emea.service@honeywell.com

Asia Pacific

Honeywell Analytics Asia Pacific

#508, Kolon Science Valley (I)

187-10 Guro-Dong, Guro-Gu

Seoul, 152-050,

Korea

Tel: +82 (0)2 2025 0300

Fax: +82 (0)2 2025 0329

analytics.ap@honeywell.com

Please Note:

While every effort has been made to ensure

accuracy in this publication, no responsibility

can be accepted for errors or omissions. Data

may change, as well as legislation, and you

are strongly advised to obtain copies of the

most recently issued regulations, standards,

and guidelines. This publication is not

intended to form the basis of a contract.

Issue 08 08/2008

H_MAN0527_2106M0514

08/08

Honeywell Sensepoint - Page 2

Table of Contents

Other manuals for Honeywell Sensepoint

Related product manuals