What to do if the bar code is displayed but not entered by my Honeywell Scanner?
If the bar code is displayed but not entered into your application, you likely need to program a suffix. Programming a suffix enables the Honeywell Scanner to output the bar code data along with the necessary key (like “CR”) to enter the data.
What to do if the bar code is displayed but not entered into the application by my Honeywell Scanner?
If the bar code is displayed but not entered into the application, you likely need to program a suffix. Programming a suffix enables the Honeywell Scanner to output the bar code data along with the necessary key (like “CR”) to enter the data.
Why won't my Honeywell Scanner read the bar code?
If your Honeywell Scanner won’t read your bar code, start by scanning the sample bar codes in the back of the manual. If the scanner reads those, then check that your own bar code is readable and that its symbology is enabled. If it still fails, scan All Symbologies.
How to fix a Honeywell Voyager 1452g Scanner that won't read bar codes?
If your Honeywell Scanner won’t read your bar code, start by scanning the sample bar codes in the back of the manual. If the scanner reads those, then check that your own bar code is readable and that its symbology is enabled. If it still fails, scan All Symbologies.
Why is my Honeywell Voyager 1452g Scanner not reading symbols well?
If the Honeywell Scanner isn’t reading symbols well, check these items: * The scanner window is clean. * The symbols aren’t smeared, rough, scratched, or exhibiting voids. * The symbols aren’t coated with frost or water droplets. * The symbols are enabled in the scanner or in the decoder to which the scanner connects.
What to do if Honeywell Scanner is not reading symbols well?
If the Honeywell Scanner isn’t reading symbols well, check these items: * The symbols aren’t smeared, rough, scratched, or exhibiting voids. * The symbols aren’t coated with frost or water droplets. * The symbols are enabled in the base or Access Point to which the scanner connects.
Why is the green LED not illuminated on my Honeywell Scanner?
If the green LED on your Honeywell Scanner isn’t illuminated, verify the following: * The scanner is correctly placed in the base. * There is external power or 12 volt host power. * Charge mode is turned on. * The battery is not bad or deeply discharged.
What to do if the red LED isn't illuminated on Honeywell Scanner?
If the red LED isn’t illuminated on your Honeywell Scanner, check that: * The power cable is connected properly and there is power at the power source. * The host system power is on (if external power isn’t used).
How to fix the aimer if it isn't illuminated on Honeywell Voyager 1452g Scanner?
If the aimer isn’t illuminated on your Honeywell Scanner, verify that: * The cable is connected properly. * The host system power is on (if external power isn’t used). * The trigger works.
General| Motion Tolerance | Up to 10 cm/s (4 in/s) for 13 mil UPC at optimal focus |
|---|---|
| Expected Charge Time | 4.5 hours |
| Storage Temperature | -40°C to 70°C (-40°F to 158°F) |
| Humidity | 0% to 95% relative humidity, non-condensing |
| Environmental Sealing | IP42 |
| Connectivity | Bluetooth, USB |
| Decode Capability | 1D |
| Battery | Lithium-ion battery |
| Drop Resistance | 1.5 m (5 ft) drops |
| Radio Range | Up to 10 m (33 ft) |
| Expected Duration of Operation | 14 hours |
| Image (Pixels) | 1040 x 720 pixel array |
Details how to connect the scanner to various host systems.
Allows creation of custom default settings for the scanner.
Process for establishing a link between scanner and charge base.
Process for establishing a link between scanner and access point.
Information about the scanner's rechargeable battery.
Crucial safety warnings for lithium batteries.
Stores bar code data when scanner is out of range or during inventory.
Allows linking multiple scanners to one base/AP.
Organizes scanners into groups for settings management.
Connects scanner to Bluetooth devices like iPads, phones, laptops.
Uses ambient light to detect bar codes automatically.
Improves reading of damaged or poorly printed bar codes.
Explains adding data before/after scanned bar codes.
Step-by-step guide to adding prefixes or suffixes.
Introduces tools to change scanner output.
Resets scanner to original factory default settings.
Restores custom default settings using a bar code.
Technical specifications for the Voyager 1450g scanner.
Technical specifications for the Voyager 1452g cordless scanner.
Guide to diagnosing and resolving corded scanner issues.
Guide to diagnosing and resolving cordless system issues.
Contact methods for installation and troubleshooting support.
Information on obtaining warranty or non-warranty service.
Details of the product's limited warranty terms and conditions.
To Next Page
